Ricoh Aficio AP2700 Service Manual Download Page 160

Page: 160 / 165

1 October, 1999

ELECTRICAL COMPONENT DEFECTS

7-15

Trouble-

shooting

7.4 ELECTRICAL COMPONENT DEFECTS

7.4.1 SENSORS

NOTE: The CN numbers describes the connector number on the engine board.

Component

(Symbol)

Condition

Symptom

Open

Toner Density

302-3

Shorted

SC390 is displayed

Open

The Paper End indicator lights even if
paper is placed in the 1st paper tray.

1st Paper End

306-2

Shorted

The Paper End indicator does not light
even if there is no paper in the 1st paper
tray.

Open

The Paper End indicator lights even if
paper is placed in the 2nd paper tray.

2nd Paper End

307-2

Shorted

The Paper End indicator does not light
even if there is no paper in the 2nd paper
tray.

Open

Image Density

321-3

Shorted

SC392 is displayed (see note)

Open

The paper overflow message is not
displayed when the paper overfull
condition exist.

Paper Over Flow

324-5

Shorted

The paper overflow message is
displayed.

Open

The Paper Jam indicator will light
whenever a print is made.

Paper Exit

324-2

Shorted

The Paper Jam indicator lights even if
there is no paper.

Open

The Paper Jam indicator will light
whenever a print is made.

Upper Relay

306-5

Shorted

The Paper Jam indicator lights even if
there is no paper.

Open

The Paper Jam indicator will light
whenever a print is made.

Lower Relay

307-5

Shorted

The Paper Jam indicator lights even if
there is no paper.

Open

The Paper Jam indicator will light
whenever a print is made.

Registration

321-6

Shorted

The Paper Jam indicator lights even if
there is no paper.

Open

SC501 will be displayed.

1st Paper Lift

305-7

Shorted

Paper jam will occur during printing.

Open

SC502 will be displayed.

2nd Paper Lift

305-10

Shorted

Paper jam will occur during printing.

Summary of Contents for Aficio AP2700






































































































































































Search results

Summary of Contents for Aficio AP2700

Reviews:

Related manuals for Aficio AP2700

Brands by name

Popular brands

Ricoh Aficio AP2700, Service Manual

Search results

Summary of Contents for Aficio AP2700

Reviews:

Related manuals for Aficio AP2700

Brands by name

Popular brands