Richmond KS10013 Assembly And Operating Instructions Manual Download Page 20

Page: 20 / 20

L. Troubleshooting

Problem

Possible Cause

Solution

Burner will not light using the
ignition system

LP gas cylinder is empty

Replace with full cylinder

Faulty regulator

Have regulator checked or replace

Obstructions in burner

Clean burner

Obstructions in gas jets or gas hose

Clean jets and gas hose

Electrode wire is loose or disconnected on

electrode or ignition unit.

Reconnect wire

Electrode or wire is damaged

Change electrode and wire

Faulty pushbutton ignitor

Change ignitor

Burner will not light with a match

LP gas cylinder is empty

Replace with full cylinder

Faulty regulator

Have regulator checked or replace

Obstructions in burner

Clean burner

Obstructions in gas jets or gas hose

Clean jets and gas hose

Low flame or flashback (fire in
burner tube

—

a hissing or

roaring noise may be heard)

LP gas cylinder too small

Use larger cylinder.

Obstructions in burner

Clean burner

Obstructions in gas jets or gas hose

Clean jets and gas hose

Windy conditions.

Use BBQ in a more sheltered position

Gas valve knob difficult to turn

Gas valve jammed

Replace gas valve

Argos Limited, MK9 2W

PDF created with pdfFactory trial version

www.pdffactory.com

Summary of Contents for KS10013





















Search results

Summary of Contents for KS10013

Reviews:

Related manuals for KS10013

Brands by name

Popular brands

Richmond KS10013, Assembly And Operating Instructions Manual

Search results

Summary of Contents for KS10013

Reviews:

Related manuals for KS10013

Brands by name

Popular brands