background image

Operation

© 

Rice Lake Weighing Systems

 

 All Rights Reserved

5

3.0

Operation

This section describes the front panel and includes procedures for operation of the scale.

Figure 3-1. Front Panel Keypad

3.1 Key Descriptions

The display has 10 front panel keys. Key functions are described in the table below.

  The front panel keys are very sensitive, so only a gentle press is required.

Key

Name

Function

On/Off

Powers the scale on or off

Print 

LB/KG

Sends data out from the RS-232 port; Allows to toggle between kilograms and pounds providing that it is enabled in 

Configuration

 mode; Cannot toggle while in the 

BMI

 mode

Zero

Only functions if the current weight is stable and less than 2% of the capacity of the scale. Anything over 2% requires 

a recalibration

Hold Release Displays most current weight value on the display and holds that value when the patient is off the scale. A second 

press releases the weight value. Not active while in 

BMI

 mode

BMI

Pressing the 

BMI

 key enables access to the BMI (Body Mass Index) mode (defaults when scale is turned on). The 

patient is gets on the scale, weight stabilizes and press the 

BMI

 key. The display then asks for the patient height to 

calculate out the patient BMI.   

TARE

Used to remove the weight initially of anything on the scale that shouldn’t be included in the total weight of the 

patient on the scale 

CLEAR

When using the BMI function, the display looks for a height entry. Pressing 

Clear

 changes this entry back to 190.0 

cm (default) or 5 ft, 7.5 in.Once BMI is displayed, pressing the 

Clear

 key exits BMI

ENTER

Used to accept height in 

BMI

 mode; accepts the value of the parameter last entered and moves to the next stage

Pressing and holding Enter during startup will display ID. This is the first setup on entering into configuration mode

Up Arrows

Adjusts the value of the flashing digit/number

Adjusts height input (0.5 in/0.5 cm) while in 

BMI

 mode

Down Arrows Adjusts the value of the flashing digit/number

Adjusts height input (0.5 in/0.5 cm) while in 

BMI

 mode

Table 3-1.  Key Functions

IMPORTANT

On/Off

LB/KG

Print

Zero

Hold

Release

BMI

TARE

T

CLEAR

ENTER

Summary of Contents for 250-10-2





























Reviews: