RIB MASTER Wi-Fi ACG6094 Manual Download Page 14

Page: 14 / 24

E -

MASTER Wi-Fi POWER

After having made all of the connections, provide power to the control panel with
MASTER Wi-Fi.
The yellow LED DL6 should come on and the buzzer will emit a sound indicating
correct power.
The LED DL7 will alternately flash red and green indicating that no remote controls
or blinkers have been memorized.

F -

IDENTIFICATION OF SAFETY DEVICES

Every Wi-Fi safety device must

OBLIGATORILY

be identified placing only one

of the 6 micro-switches present on its circuit (different for each of the 6 safety
devices) in the ON position. Obviously one pair of photocells is considered one
safety device and must therefore have a receiver and transmitter with the same
DIP in the ON position.

IDENTIFY THE CONTAINERS OF THE SAFETY DEVICES WITH THE NUMBER
OF THE ACTIVATED MICRO-SWITCH AND ATTACH THE NUMBERED
ADHESIVE STRIP SUPPLIED TO THE OUTSIDE OF EACH CONTAINER.

The adhesive strip serves as a means of quickly identifying the safety device when
it needs maintenance.

Note:

Each safety device is supplied with the micro-switches in the OFF position

so that battery power is not consumed when not in use (if inserted).
Insert the batteries in the Wi-Fi safety devices.

G -

MEMORIZATION OF THE SAFETY DEVICES

After having performed the identification of the safety devices, and provided power
with the batteries,

place the micro-switches

with the same number of the safety

devices on the MASTER Wi-Fi

in the ON position

to activate the safety devices

to be memorized.
Use the following procedure for memorization:

- Push the button PROG RX on the MASTER Wi-Fi

=> dual-color LED EDGE

PHOT 1 flashes red for 1 minute (the time needed for memorization).

- Push the button PROG TX on the safety device with micro-switch 1 in

the ON position

=> on the MASTER Wi-Fi the dual-color LED EDGE PHOT 1

flashing red turns green and a sound from the buzzer indicates that the safety
device has been memorized correctly, immediately the dual-color LED EDGE
PHOT 2 begins flashing red.

- If there are no other safety devices to be memorized after one minute

the

dual-color LED EDGE PHOT 2 will turn off

or, push the button PROG. RX 4

times to end the memorization procedure

=> all of the dual-color LED EDGE

PHOT should be off.

MEMORIZATION OF OTHER SAFETY DEVICES
- After having memorized the first safety device,

the dual-color LED EDGE

PHOT 2 automatically begins flashing red for 1 minute (the time needed for
memorization).

Push the button PROG. TX on the safety device with micro-switch 2 in the ON

position => on the MASTER Wi-Fi the dual-color LED EDGE PHOT 2 flashing
red turns green and a sound from the buzzer indicates that the safety device has
been memorized correctly.

Follow the same procedure for any other safety devices (up to a maximum of 6).

ADDING OTHER SAFETY DEVICES (UP TO 6 TOTAL)

If after installation the use of further safety devices (PHOTOCELLS OR STRIPS)
is desired, to increase door safety, it is recommended to:
-

Turn off power to the door.

Place the safety device in the desired position and identify it by moving the
internal micro-switch.

Perform the programming by setting to ON a micro-switch different from that of
the other safety devices installed and identify it with the corresponding numbered
adhesive strip (see paragraph F - IDENTIFICATION OF Wi-Fi SAFETY
DEVICES).

Enable the micro-switch of the safety device just added on the MASTER Wi-Fi
card.

Return power to the door.

Follow the memorization procedure and system check as indicated previously.

NOVA Wi-Fi AND VERTIGO PHOTOCELLS SYSTEM CHECK

Check that the micro-switch selected on the transmitter TX NOVA Wi-Fi is the
same as that selected on the receiver RX NOVA Wi-Fi (example 1 ON).

Proper function of the TX NOVA Wi-Fi is shown by the green LED which comes
on for 10 seconds.

Push and release the button S3 “PROG. TX” on the NOVA Wi-Fi receiver (it
activates for 3 minutes to perform the alignment procedure). If the photocells are
already aligned the red LED emits a constant light. If the red LED is off or emits
a flashing light, perform the alignment until it emits a constant light.

After the alignment check by placing an obstacle that the red LED turns off and
that at the same time the dual-color LED EDGE PHOT associated with it during
memorization shines green on the MASTER Wi-Fi for the time that the obstacle
is present.

On the MASTER Wi-Fi card, LED DL3 should also be off indicating a proper
exchange of the dedicated input with the PHOT on the control panel.

Repeat the procedure on the other installed NOVA Wi-Fi photocells.

Perform a function check of all the installed photocells, activating the movement
of the automation and checking that by placing an obstacle the automation stops/
reverses when closing, or stops/continues to open when opening.

TOUCH Wi-Fi STRIP SYSTEM CHECK

After having calibrated the TOUCH Wi-Fi strip correctly:
-

Push the contact of a TOUCH Wi-Fi strip (for example: safety device number 3).

On the MASTER Wi-Fi check that the corresponding LED EDGE PHOT 3 flashes
green and that the paired LED DL2 momentarily turns off and then turns on.

ATTENTION:

after receiving the first signal, other signals are ignored for 2

seconds. If there is a signal in these 2 seconds it will be from the LED EDGE
PHOT 3 which turns green.

the

“SELF-TEST-ENABLED RIB ELECTRONIC BOARD CHART”

or by the

control panel power supply used (see relative instructions).

Connect the auto test output of the control panel to the A/D+ TEST terminal of
the MASTER Wi-Fi card in order to be able to control the system at the end of
every complete automated opening.

Closing will only occur when the MASTER Wi-Fi card has passed the

control test.

If the MASTER Wi-Fi card control test fails, the control panel will block the

automation, the dual-color LED on the MASTER Wi-Fi card indicates a safety
outage, alternately flashing red and green.

The buzzer emits an alternating sound for 1 minute to signal the problem.

The alarm status of the buzzer comes on again for 1 minute when a control is
given.

If the panel is not equipped with an auto test, the control test is ignored.

SELF-TEST-ENABLED RIB ELECTRONIC BOARD CHART

K2007 / K2007 CRX
S1
T2 - T2 CRX
T2 24V - T2 24V CRX
J - J CRX
BOSS 24V CRX
BOSS 230V CRX

RIB ELECTRONIC BOARD

A+ TEST
A+ TEST
D+ TEST
A+ TEST
D+ TEST
Terminal 8
Terminal 8

CONNECT A/D+ TEST TERMINAL
TO TERMINAL