repeat the procedure described above.
AUTOMATIC PEDESTRIAN CLOSING
Pause times before the automatic pedestrian closing of the gate are set during the
programming procedure.
The max. pause time is 5 minutes.
You can start or stop the pause time using
DIP3
(ON starts).
SAFETY EDGE IN OPENING (11-12)
If the safety edge intervenes during the opening of the gate, it commands the reversal of
the movement. This reversal will continue even if the safety edge remains pressed.
During closing the safety edge is not active.
When the safety edge is not in used contacts 11-12 must be bridged.
PHOTOCELL 2 (9-12)
If it detects an object during the opening cycle, it then operates the closing of the gate at
the end of the interposition. If it detects one during the closing cycle, it then operates the
opening at the end of the interposition.
This function is particularly helpful when you want the gate to close immediately after you
passed it.
If it is not used, jumper the terminals 9-12.
N.B.: Every six months make sure to check that photocells are not out of order
COURTESY LIGHT (7-8)
It is possible to supply 24Vac power to the coil of a relay, so as to feed one lamp or more
for a minimum period of 1 second and for a maximum period of 4 minutes (controlled by
the TR trimmer fitted on the EXPANDER card).
The relay is activated at every opening or closing.
When the closing is finished, the traffic light turned off.
TRAFFIC LIGHT CONTROL
When the gate is closed, the traffic light is turned off.
The red light
(3-4) turns on when the gate opens.
The green light
(5-6) turns on when the gate is open and the red light turns off.
The green light remains turned on until the automatic closing starts.
When the gate closes, the green light turns off and the red light turns on.
RADIO TRANSMITTER MOON
CODE LEARNIG SYSTEM RADIORECEIVERS
RX91/A
quarzata and coupling
code ACG5005
RX91/A
quarzata and terminal board
code ACG5004
RX433/A
super eterodyne and coupling
code ACG5055
RX433/A
super eterodyne and terminal board
code ACG5056
RX433/A 2CH super eterodyne, 2 channel and coupling
code ACG5051
RX433/A 2CH super eterodyne, 2 channel and terminal board
code ACG5052
Pag. 18 di 24
BLOCK
BLOCK KEY SELECTOR FOR WALL-INSTALLATION
code ACG1053
BLOCK KEY SELECTOR TO BUILD-IN
code ACG1048
MECHANICAL STRIP
L=2MT - 6,56 FEET
code ACG3010
With double-safety contact, you can cut the length you need.
FIT SYNCRO
FIT SYNCRO PHOTOCELLS FOR THE WALL-INSTALLATION
- code ACG8026
The range you can set Is 30÷60ft 49÷100”.
You can fit many couples close together thanks to the synchronising circuit.
Add the
SYNCRO TRANSMITTER
, code ACG8028, for more than 2 photocells couples
(up to 4).
COUPLE OF BUILT-IN BOXES FOR THE FIT SYNCRO
code ACG8051
ACG6081 - 433
ACG7025 - 91
ACG6082 - 433
ACG7026 - 91
E
N
G
L
I
S
H
SPARK ANTENNA
In order to make the systems mentioned above give the best performances, you need to
install an antenna tuned on the frequency of the radio receiver installed.
N.B. Pay attention not to let the central wire of the cable to came Into contact with
the external copper sheath, since this would prevent the antenna from working.
Install the antenna vertically and in such a way the remote control can reach it.
SPARK ANTENNA 91
code ACG5454
SPARK ANTENNA 433
code ACG5252
SPARK BLINKER
with in-built intermittent card
code ACG7010
