manualshive.com logo in svg

RHINO Multi-Pro 301002, Owner'S Manual

Share
Download
RHINO Multi-Pro 301002 Owner'S Manual Download Page 23

21

Rhino

®

 Multi-Pro

™

 Parts and Accessories List

No.

P/N

Description

1

300712

Ground Bolt

2

301016

Body Assembly with Cylinder and Bearings

3

301222

Top Handle Assembly

4

300715-4

Pro Series Handle Bolt (qty. of 4)

5

301221-2

Handle Collar Set (qty. of 2)

6

610010-4

Handle Springs (qty. of 4)

7

300214 Top Handle Bracket

8

301075

Piston and Connecting Rod Assembly

9

301610-2

Piston and Hammer O-ring Seal Set (qty. of 2)

10

301085

Multi-Pro™ Hammer

11

301115

Multi-Pro™ Anvil O-ring Retainer

12

301614-2

Large Retainer O-ring Seal Set (qty. of 2)

13

301105

Multi-Pro™ Large Retainer

14

301095

Multi-Pro™ Anvil O-ring Cup

15

301165 Anvil (See page 27 for Extended Anvil.)

16

301615

Multi-Pro™ Anvil O-ring Seal

17

301710

Multi-Pro™ Body Gasket

18

301038

Multi-Pro™ Sleeve for Lower Body

19

301032

Multi-Pro™ Lower Body

20

300750-4

Multi-Pro™ Lock Washers (qty. of 4)

21

300701-4

Lower Body Bolt Set (qty. of 4)

No.

P/N

Description

22

301158

Multi-Pro™ Master Chuck

23

300717-4

Multi-Pro™ Chuck Bolt Set (qty. of 4)

24

301920

Chuck-Lok

™

 Locking Nut (1 per driver)

25

300221  8.5" (216mm) EPDM Foam Grip (1 per driver)

26

301232

Pro-Series Side Handle Assembly

27

300250

Throttle Control Assembly

28

301233

Lower Handle Assembly

29

300900

Chuck-Lok

™

 System 1" 

(25.4 mm) Adapter

30

300895

Chuck-Lok

™

 System 1¾" 

(44.45 mm) Adapter

31

300902

Chuck-Lok

™

 System 2" (50.8 mm) Adapter

Summary of Contents for Multi-Pro 301002

































Reviews:

No comments

Brands by name

Popular brands

Load more brands