RHEONIK RHE 07 Operation Manual Download Page 8

Page: 8 / 50

RHEONIK Messgeräte GmbH

REV. I, Apr. 2004

Operation Manual RHE 07, 08, 11

Page

fixation screw

If you are connecting flexible tubing or hose

directly to the sensor please use sensor

housing flanges for rigid sensor mounting. In

order to insure a stable zero point, the sensor

must be firmly installed.

Use a high quality valve downstream from the

sensor for proper zero point calibration. For

sensor sizes

RHM 015, 03 und 04

two valves,

upstream and downstream, are recommended. Since the piping is not stable, we recommend install-

ing these sensor sizes directly on the connection block.

For mechanical installation of these small meters we recommend a mounting skid made of alumin-

ium, in order to achieve an optimum of stability with low installation time and costs.

Installing scheme with holder:

The sensor RHM, as well as the measuring cable (RHM/RHE) must be installed as far away from

sources of electrical interference (transformers, high tension switching components, large electrical

motors, frequency converters, etc.) as possible.

sensor RHM ..

connection block

fixation screw

mouting skid for wall mounting

wall or rigid skid

Summary of Contents for RHE 07



















































Search results

Summary of Contents for RHE 07

Reviews:

Related manuals for RHE 07

Brands by name

Popular brands

RHEONIK RHE 07, Operation Manual

Search results

Summary of Contents for RHE 07

Reviews:

Related manuals for RHE 07

Brands by name

Popular brands