Rheem RTGH-84DVLN-2 Use And Care Manual Download Page 1

Page: 1 / 84

95% CONDENSING

TANKLESS

WATER HEATER

AP18161-1 (11/16)

Do not destroy manual. Please read

carefully and keep in a safe place

for future reference.

CERTIFIED

WARNING:

This water heater is not suitable

for use in manufactured (mobile)

homes.

WARNING:

If the information in these

instructions is not followed

exactly, a fire or explosion may

result, causing death, personal

injury, or property damage.

For Your Safety!

• Do not store or use gasoline

or other flammable vapors and

liquids in the vicinity of this or

any other appliance. To do so

may result in an explosion or

fire.

• Installation and service must

be performed by a qualified

installer, service agency, or the

gas supplier.

What to Do If

You Smell Gas

• Do not try to light any

appliance.

• Do not touch any electrical

switch; do not use any

phone in your building.

• Immediately call your gas

supplier from a neighbor’s

phone. Follow the gas supplier’s

instructions.

• If you cannot reach your

gas supplier, call the fire

department.

• Do not return to your home until

authorized by the gas supplier

or fire department.

DESIGN

CERTIFIED

USE AND CARE MANUAL

With Installation Instructions

for the Installer

Condensing Direct Vent and Outdoor

199,900 Btu/hr, 180,000 Btu/hr and

157,000 Btu/hr Models

Summary of Contents for RTGH-84DVLN-2





















































































Search results

Summary of Contents for RTGH-84DVLN-2

Reviews:

Related manuals for RTGH-84DVLN-2

Brands by name

Popular brands

Rheem RTGH-84DVLN-2, Use And Care Manual

Search results

Summary of Contents for RTGH-84DVLN-2

Reviews:

Related manuals for RTGH-84DVLN-2

Brands by name

Popular brands