background image

SECTION II: GENERAL INFORMATION

loCaTIon

The indirect water heater should be located in a central location to the piping system, as close as 
practical to the boiler and in an area not subject to freezing temperatures.  Leave sufficient space 
for servicing and maintaining the indirect water heater.

NOTICE:

 Long heating supply runs can lengthen recovery times.

WaTer TreaTmenT/fIlTraTIon

In areas where poor water conditions are suspected (i.e. lime, iron, and other minerals), it is 
essential that the water be tested and appropriate action taken to prevent damage to the indirect 
water heater and ensure the quality of the water.

TemperaTure ConTrol

Water temperature from the heat source / boiler to the indirect water heater is controlled by an 
immersion aquastat. This control operates the  circulator, and provides limited control for 
 domestic hot water temperature. The proper temperature setting for  domestic hot water use is 
120°F/49°C. If hotter water is required a tempering device or anti-scald device must be installed at 
the domestic hot water outlet of the indirect water heater or at the point of use.

CAUTION: Hot water in excess of 120

°

F  

can cause scalding!

Rheem recommends a tempering valve or anti-scald valve be  installed and used according to the 
manufacturer’s directions to prevent scalding. Many state and local codes now require 
installation of these devices. The tempering valve or anti-scald valve will ensure potable water 
temperatures at the desired set point with a higher degree of accuracy.

IMMERSION CONTROL

STID30 

 STID40 

 STID50 

 STID80 

 STID120

APPROXIMATE

TEMPERATURE/TIME

RELATIONSHIPS TO

SCALDING

 

120°F 

More than 5 minutes

 

125°F 

1

¼

2  

to 2 minutes

 

130°F 

About 30 seconds

 

135

°F 

About 10 seconds

 

140°F 

Less than 5 seconds

 

145°F 

Less than 3 seconds

 

150°F 

About 1 

1

¼

2  

seconds

 

155°F 

About 1 second

 

Page 5

Summary of Contents for Indirect Water Heater

















Reviews: