manualshive.com logo in svg

Rheem 627 series, Owner'S Manual And Installation Instructions, Page: 43 / 56

Share
Download
Rheem 627 series Owner'S Manual And Installation Instructions Download Page 43

 

43 

CONNECTIONS – ELECTRICAL 

 
All electrical work and permanent wiring must be carried out by a qualified person and in accordance with the 
Wiring Rules AS/NZS 3000 and all local codes and regulatory authority requirements. 
 

 

Warning:

 Temperature controllers 

must not

 be fitted to this water heater (862 series) if it is installed as 

an in-series gas booster with a solar water heater system or if a Water Star water heater is installed because 
water  at  a  temperature  much  higher  than  the  controller  setting  can  be  delivered.  If  a  solar  or  Water  Star 
water  heater  has  been  installed  to  an  existing  water  heater  installation,  then  all  controllers 

must be

 

disconnected and removed. 
 
The  water  heater  is  supplied  with  a  1.8 metre  lead  and  plug  and  requires  a  240 V  50 Hz  general  purpose 
outlet (GPO) to be located within 1.2 metres of the installation. The GPO must be clear of the flue exhaust, 
draining water, gas supply pipe and water connections. 
 
The power consumption of the water heater is: 
 
 

Component 

Power 

consumption 

Comments 

Gas water heater 

80 Watts 

627 

– Burner on, anti frost device inactive 

 

187 Watts 

627 

– Burner on, anti frost device active 

 
 
The  water  heater  will  only  operate  on  a  sine  wave  at  50 Hz.  Devices  generating  a  square  wave  cannot be 
used to supply power to the water heater. 
 
 

Summary of Contents for 627 series

























































Reviews:

No comments