manualshive.com logo in svg

Rheem 627 series, Owner'S Manual And Installation Instructions, Page: 3 / 56

Share
Download
Rheem 627 series Owner'S Manual And Installation Instructions Download Page 3

 

3 

CONTENTS 

 
 

RESPONSIBLE OFFICER - We recommend you read pages 4 to 14. 

The other pages are intended for the installer but may be of interest. 

 
 

About Your Water Heater ............................................................................................................ 4

 

Water Supplies ........................................................................................................................... 11

 

Save A Service Call ................................................................................................................... 12

 

Installation 

– Water Heater ....................................................................................................... 15

 

Connections 

– Plumbing .......................................................................................................... 24

 

Flueing ........................................................................................................................................ 26

 

Connections 

– Electrical ........................................................................................................... 43

 

Multiple Installations ................................................................................................................. 44

 

Commissioning .......................................................................................................................... 47

 

Draining The Water Heater ....................................................................................................... 54

 

Warranty ..................................................................................................................................... 55

 

 

Summary of Contents for 627 series

























































Reviews:

No comments