RF Electronics RF-T860/24 Installation & Operation Manual Download

Page: 13 / 13

RF-T860 Optical Transmitter

Page 10

Installation and Operation Manual

7. Trouble shooting

Trouble

Reason.

Solution

Power on, the LCD

is off.

Switch Power

is abnormal.

Check the power socket,

connect the supplier to get help.

Power

on,

alarm

signal shows on the
LCD.

1.The

Operating
Temperature is
too low, waiting
for a moment.

2.Waiting for

a moment after
power on.

The software would reset the

automatically, otherwise, please
press the RESET key.

If the machine still can’t work

after you press the RESET key for
several times, please cut off the
power and contact the supplier.

Power

on,

LCD

shows normally, but
Optical

Power

abnormal

The optical

connector is
dirty.

Clean connector ends with a

lint free tissue and alcohol (above
99%) before mating. Loose
screws fixing the optical connector
plate to clean the connector when
it is necessary.

All manuals and user guides at all-guides.com

Summary of Contents for RF-T860/24














Search results

Summary of Contents for RF-T860/24

Reviews:

Related manuals for RF-T860/24

Brands by name

Popular brands

RF Electronics RF-T860/24, Installation & Operation Manual

Search results

Summary of Contents for RF-T860/24

Reviews:

Related manuals for RF-T860/24

Brands by name

Popular brands