background image

 

1307SDH_RDH--EN,

page 27/32 

12.6  Fan motor, fan 

 
The fan motor is equipped with thermal overload 
protection of the automatic reset type.  Should the motor 
fail to run, it may be because of improper voltage 
characteristics.  Make certain that the correct voltage is 
available at the motor.  
Remove dirt and grease from the motor and the fan. Use 
care when cleaning the fan to prevent imbalance. 
 
 
 
 

12.7  Venter motor & wheel 

 
See figures 30 & 31 
 
Remove dirt and grease from the motor casing, the 
venter housing, and the venter wheel. Venter motor 
bearings are permanently lubricated. 
Follow these instructions for replacement of the venter 
motor and wheel assembly. Keep all hardware removed 
to be used in reassembling and installing the 
replacement parts. 
1.  Turn off the gas and disconnect the electric power. 
2.  Open the control compartment access door.  
3.  Disconnect the three venter motor wires at the 

terminal and ground screw . 

4.  Holding the motor, remove the screws that attach 

the motor plate to the venter housing. Remove the 
motor and wheel assembly from the heater. 

5.  Reassemble with the replacement venter motor and 

wheel assembly. 

6.  Follow the wiring diagram to properly connect the 

wires.  

7.  Restore power to the heater and turn on the gas. 

Light, following the instructions on the lighting 
instruction plate. Check for proper operation. Close 
the access door. 

 
 
 
 

Figure 30 : AACO motor 
types SDH/RDH 025

055 

 

 
 

Figure 31 : AACO Venter assembly 
types SDH/RDH 073 & 100  

 

 

 
 

 

12.8  Operating gas valve 

 
See figure 32 
 
The main operating quick opening gas valve is powered 
through the thermostat and safety controls.  The main 
control valve is of the diaphragm type providing 
regulated gas flow and is adjusted at the factory. The 
gas valve requires no field maintenance except careful 
removal of external dirt accumulation and checking of 
wiring connections. Instructions for testing pressure 
settings are in sections 9 and 10. 
 

 
 

 
 
 
Figure 32 : Gas valve, (nat.gas)) 

 

 
 
 

Summary of Contents for RDH 025


































Reviews: