manualshive.com logo in svg

Reynolds Building Systems the Richmond, Assembly Book, Page: 18 / 20

Share
Download
Reynolds Building Systems the Richmond Assembly Book Download Page 18

Building Tip:

Ridge vent provides ideal

ventilation, preventing heat or moisture from
damaging your building or its contents.

Cut Top Row to Fit

Ridge vent provides

ideal ventilation.

Truss

Shingles

Air
Space

Straight Edge

Truss

DETAIL 'B'

Step 17 Install Roof Sheathing

Building

Front

96" Long

48"x 72"

48"x 96"

Install This Row of Roof Sheathing First

48"x 96"

48"x 96"

48"x 51"

37-3/8"x 96"

Plyclip

Install a plyclip between each truss
on the top row of sheathing .

96" Long

51" Long

37-3/8"x 72"

37-3/8"x 75"

48"x 75"

Cut Sheathing From Pallet

"

"

Install 7/16" OSB roof sheathing according to the layout below. Install roof sheathing flush
with the 2x4 on the rear gable. Install the lower sheathing first. Use a straight edge to align
the top of the sheathing with the top of the truss. See Detail 'B'. If you are installing ridge

vent, cut the roof sheathing at the top of the building to be 1" below the peak of the truss.
This will allow air circulation through the ridge vent.
Install sheathing using 7d sinkers. Space nails 12" apart.

Summary of Contents for the Richmond





















Reviews:

No comments