Reynolds Building Systems BEST BARNS Northwood Deluxe Assembly Book Download | Manualshive

Page: 16 / 20

background image

1.

Secure the front of the trusses to the H1 hangers with 1-1/2" hanger nails.

2.

Locate (4) four 21"x48-3/4" soffit panels under the front overhang. Cut the first soffit panel

along 'LAP' edge so the tongue edge is centered on the second truss. Use 6d galv. nails.

3.

Install another soffit panel. Cut the last panel to fit.

Step 15 Install Gable Trim

Step 14 Install Front Soffit

Install the 1x4 gable trim extending 1/2" above the 2z4
on the gable. When installed later, the roof sheathing
will be flush with the top of the trim.

Siding/Soffit Panel

Trim 1/2"

Above 2x4

«
...
14
15
16
17
18
...
»

Summary of Contents for BEST BARNS Northwood Deluxe





















Reviews:

No comments

Related manuals for BEST BARNS Northwood Deluxe

Brand: Palmako Pages: 62

Brand: STILLA Pages: 60

Brand: Palmako Pages: 27

Brand: Palmako Pages: 30

Brand: Palmako Pages: 44

Brand: GardenMeister Pages: 45

12x12 SpaceMaker Garden Shed

Brand: OLT Pages: 46

Brand: Palmako Pages: 93

Brand: Skan Holz Pages: 19

White Wood FRJ40-4040

Brand: Palmako Pages: 56

Brand: Karibu Pages: 40

Brand: VERANDA JARDIN Pages: 28

Brand: verhaeghe Pages: 8

HA28001-4163162451-21-0000-20

Brand: megiw Pages: 35

HA28001-3163162453-12-0000-20

Brand: megiw Pages: 30

Brand: Forest garden Pages: 2

8' x 6' Overlap Apex Shed

Brand: Forest garden Pages: 2

3' x 5' Value Shed

Brand: Forest garden Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands