Reynolds Building Systems BEST BARNS Northwood Deluxe Assembly Book Download | Manualshive

Page: 10 / 20

background image

Step 7

Assemble Door Walls

31-3/4" Plate

10-3/4" Plate

71-1/2" Header

Support

71-1/2" Header

Support

31-3/4" Plate

10-3/4" Plate

16-1/2"

1.

Gather (3) three 72" wall studs and (2) two 31-3/4" long 2x4 wall plates. Assemble left side

wall frame as shown below. Use 10d sinkers.

2.

Attach (1) one 71-1/2" long 2x4 as a header support to end of frame. Top of 2x4 will be 3-1/2"

below top plate. Use (4) four 10d sinkers.

3.

Gather (2) two 72" wall studs and (2) two 10-3/4" long 2x4 wall plates. Assemble right side

wall frame as shown below. Use 10d siners.

4.

Attach (1) one 71-1/2" long 2x4 as a header support to end of frame. Top of 2x4 will be 3-1/2"

below top plate. Use (4) four 10d sinkers.

Left Side Wall Frame

Right Side Wall Frame

3-1/2" Below

Plate

3-1/2" Below

Plate

«
...
8
9
10
11
12
...
»

Summary of Contents for BEST BARNS Northwood Deluxe





















Reviews:

No comments

Related manuals for BEST BARNS Northwood Deluxe

Brand: Palmako Pages: 54

Veronica PA34-3434-1

Brand: Palmako Pages: 67

Sandy 5.0 FRF34-4432

Brand: Palmako Pages: 36

Brand: Solid Pages: 16

Brand: Outdoor Life Products Pages: 30

Brand: Outdoor Life Products Pages: 28

Brand: ABSCO SHEDS Pages: 26

Brand: Palmako Pages: 53

Brand: Palmako Pages: 63

Brand: Lemeks Pages: 55

Brand: Lemeks Pages: 59

Brand: Lemeks Pages: 67

PALMAKO ANDRE EL18-4555-4

Brand: Lemeks Pages: 56

Brand: Lemeks Pages: 153

Brand: Lemeks Pages: 154

Brand: G21 Pages: 40

Skylight Shed 4x6

Brand: Palram Pages: 48

Brand: gardenas Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands