manualshive.com logo in svg

Reynolds Building Systems BEST BARNS Northwood Deluxe, Assembly Book

Share
Download
Reynolds Building Systems BEST BARNS Northwood Deluxe Assembly Book Download Page 11

Step 8

Install Siding on Door Wall

If you want the door opening on the left, flip the walls and apply siding
to the opposite side of the wall frames.

3.

Install a 21-1/2" wide siding panel. The siding will extend 3-1/2" beyond the wall frame.

21-1/2" Wide Siding Panel

2.

Locate a pre-cut 16" wide siding panel that has a 'LAP' edge. Position this panel with the

 'cut' edge flush with the 2x4 header support and extending 3/4" below the bottom plate.
Do not nail along the LAP edge until the other siding panel is installed.

2x4 Header Support

Cut Edge

LAP Edge

1.

Select the larger door wall frame.

Siding Extends

3-1/2" Past Wall Frame

4.

Install a pre-cut 16" wide siding panel with the 'cut' edge flush with the 2x4 header support.

The siding will extend 3-1/2" beyond the wall frame and 3/4" below the bottom plate.

71-1/2" Header

Support

Cut Edge

Tongue Edge

Siding Extends

3/4" Below plate

Siding Extends

3/4" Below plate

Siding Extends

3-1/2" Past Wall Frame

Summary of Contents for BEST BARNS Northwood Deluxe





















Reviews:

No comments

Brands by name

Popular brands

Load more brands