manualshive.com logo in svg

Reynolds Building Systems Best Barns Meadowbrook-R, Assembly Book, Page: 7 / 20

Share
Download
Reynolds Building Systems Best Barns Meadowbrook-R Assembly Book Download Page 7

5.

Assemble the loft doors. The loft door frames are

temporarily held together with corrugated fasteners,
this is the back side of the door frame. Place the
doors on level surface, face side down. Cut the siding
from above step to the size of the door frame. Secure
the siding panel to the frame with 1" screws provided.

24-3/4"

Step 4

Assemble Roof Gable With Loft Doors

1.

Assemble another gable frame. Create an opening

for the loft doors by installing a 36" long 2x4 between
the gable studs. The opening height should 24-3/4"
from the bottom 2x4 truss member.

36" Long 2x4

34-1/4" Long

Gable Stud

4.

Nail siding on the gable. Use 6d galv.

nails. spaced 12” apart.

3.

Cut siding from the loft door opening, flush with

the edge of the opening.Save cutouts for loft doors.

If you don't need loft access from the outside, attach loft door frames to
the gable to create a decorative look and weather tight storage area.

Supplied in Kit

1"x4" Drive-on Plate

38" Long Gable Rafter

47 Long Gable Rafter

2.

Turn the gable over. Locate pre-cut gable siding. Starting from left place the siding extending

3/4" below the bottom 2x4. Insure the siding does not extend above the top frame. Do not nail
to frame until opening for loft door is cut out.

Summary of Contents for Best Barns Meadowbrook-R





















Reviews:

No comments