manualshive.com logo in svg

Reynolds Building Systems Best Barns Meadowbrook-R, Assembly Book, Page: 5 / 20

Share
Download
Reynolds Building Systems Best Barns Meadowbrook-R Assembly Book Download Page 5

Siding Extends

3/4" Below Plate

Tip; To prevent gable studs from
being knocked loose when nailing
siding, lay 2x4 OSB sheathing,
supplied in kit, under the studs.

Step 2

Assemble Roof Gable Without Loft Doors

5.

Turn the gable over. Locate pre-cut gable siding. Starting from left install the siding extending

3/4" below the bottom 2x4. Insure the siding does not extend above the top frame. Use 6d galv.
nails. Space 12" apart.

Supplied in Kit

34-1/4" Long Gable Stud

21-1/2" Long Gable Stud

4.

Screw (3) three 16" long 2x4 blocks

across the bottom of the 2x4 bottom
cord. Use 2-1/2" screws.

35-3/4" Long Center Stud

1.

Place (2) two 47" long and 38" long 2x4 gable rafters, packed in extension kit,  in the truss

jig and secure with 1"x4" drive-on plates.  Toenail a ridge block at the ridge.

2.

Secure 2x4 gable studs to the truss with (10) ten 1"x4" metal plates.

3.

Install  wood gusset to bottom of truss and the ridge.

1"x4" Drive-on Plate

38" Long Gable Rafter

47 Long Gable Rafter

1"x4" Drive-

on Plate

1"x4" Drive-

on Plate

Wood Gusset

LAP

Summary of Contents for Best Barns Meadowbrook-R





















Reviews:

No comments