![background image](http://html1.mh-extra.com/html/rexel/prostyle-5/prostyle-5_instruction-manual_1449363005.webp)
5
G
Warranty
ACCO Brands Europe (ACCO) warrants its products and their parts
against defects in materials and workmanship under normal use for a
period of 12 months from the original date of purchase.
During this period we will repair or replace a defective product or part
subject to the following warranty conditions:
The warranty applies only to defects in materials and workmanship
under normal use and does not extend to damage to the Product or
parts which result from:-
- alteration, repair, modification or service carried out by anyone other
than an authorised ACCO service centre.
- accident, neglect, abuse or misuse owing to failure to comply with the
normal operating procedures for a product of this type.
Depending on the diagnostics and the model type, we will either arrange
a service call by an engineer or arrange with you return of the product to
ACCO. ACCO will, at its discretion, in accordance with law, either
- repair the shredder using either new or refurbished parts, or
- replace the shredder with a new or refurbished shredder that is
equivalent to the shredder being replaced.
Nothing in this Warranty shall have the effect of excluding the liability of
ACCO in respect of death and personal injury caused by the negligence
of ACCO. This Warranty is offered (subject to these terms and conditions)
in addition to, and does not affect, your statutory rights.
If you experience a technical fault, please contact the ACCO customer
helpdesk (see back cover).
Register this product online at
www.accobrands.com
Preparation before use
How to use the shredder correctly:
1
Take care not to insert fingers, ties or other objects into the entry
slot of the shredder.
2
Try to avoid laminating materials, plastic bags etc. from being
passed through the shredder. This will prevent damage to the
cutters.
3
Do not shred wet paper as it can tangle in the cutters.
4
Do not shred more than the stated sheet capacity in one pass.
5
Do not use the “REV” ( ) (reverse) function if it’s not necessary.
Over use of the “REV” ( ) function can result in shredded paper
becoming jammed in the entry slot, which will adversely affect the
performance of the shredder.
Installation
Position the shredder onto the basket (fig 1). Once the unit is
correctly positioned on the basket, plug it into a standard AC
outlet.
NOTE:
The cross-cut models include safety interlocks. If the bin is not
fully pushed into the cabinet, the interlocks will not be activated and the
unit will not operate.
Forward and reverse (fig 5)
In case of jammed paper, please follow the procedure below:
1
Check if the bin is too full with paper - the bin should be emptied
regularly to avoid paper becoming jammed in the cutters.
2
Slide the switch to ‘REV’ position to reverse the jammed paper.
3
If the paper is so jammed that it will not come out in reverse
function, slowly push the switch between ‘REV’ and ON/AUTO. Don’t
do this too quickly as this can damage the shredder.
4
WARNING –
Do not under any circumstances use any metal objects
(scissors, letter openers etc.) in an attempt to clear the entry – this
model has mains voltage inside the casing, which could cause
serious injury.
Correct operating procedure (fig 2)
1
Insert plug into the AC power socket.
2
Push the switch to the ON/AUTO position (standby mode)
3
When not in use, push the switch to the O (off position)
Auto shred and stop
• Place the paper (fig 3) or credit card (fig 4) into the centre of the entry
slot - shredding will start automatically.
• Paper smaller than A4 in width should be placed in the middle of the
entry slot to ensure the shredder works automatically.
• The cutters will stop rotating automatically after finishing shredding
• Do not shred more than the stated sheet capacity at a time.
Troubleshooting
If the paper shredder will not start, please check the following:
1
Is the machine plugged in correctly?
2
Is the switch pushed to the ‘ON/AUTO’ position?
3
Is the machine jammed with paper?
4
Has the motor overheated?
5
Is the shredder bin fully pushed in?
This machine does not require lubricant. Acco Brands Europe accepts no
liability for product performance or safety should any lubricant be used
on any part(s) of this machine.