background image

3) Specifications

4) Main parts

Table. 1

Model

Use

Size

( W x D x H )

Unit: Approx. 146x109x61mm

˴

Power cord: 2m

Weight

Main unit: 335g / Power cord: 85g

Battery type

Lithium-ion battery

Voltage

AC220V

50

60Hz

60VA

Charging system

Constant current and constant
voltage system

Charging voltage

Charging current

10

8V

Operating temperature

0

40

͠

2000mA

Circuit protector

Overcharge protection (4.25V/cell)

Overcurrent protection (7A fuse)

RF20SC

For charging REX lithium-ion battery
RF20SB (No. 424982)

7. Do not charge continuously with the same charger.

- If the same charger is used to charge a number of tools continuously, it could overheat and be damaged.

Once charging is finished, leave the charger to cool for about 15 minutes before charging again.

8. Do not immediately recharge a battery that has been used up quickly.

- A storage battery that has been exhausted quickly due to continuous operation becomes abnormally hot.

Therefore, when such a battery is placed in the charger, a red pilot lamp comes on, either preventing a recharge,
or resulting in an insufficient charge. Always charge the battery after it has cooled down.

9. Do not charge for more than 2 hours.

- If the pilot lamp stays on even after charging for 2 hours, the charger may be faulty. Stop charging and consult

your nearest distributor.

10. Keep the battery-mounting socket clean.

- The battery-mounting socket on the charger has charging terminals. If this socket is contaminated with metal chips,

water or other foreign bodies, the terminals may be short-circuited, causing damage to the charger.

11. Do not attempt to disassemble either the storage battery or the charger.

- The charger and the storage battery houses condensers and electronic parts.

Disassembly could result in electric shock or damage to the charger; never try to disassemble them!

12. Never short-circuit the charger.

- The lithium-ion battery used with this unit has an extremely low internal resistance. If short-circuited, there may be

a surge in the current, resulting in overheating, burns or damage to the battery.

13. Never put the storage battery in a fire.

- Never put the battery in a fire or an incinerator or it may explode.

14. Keep the ventilation hole on the charger clean.

- Keep the ventilation hole on the charger clear of metal chips and inflammable materials as they may cause electric

shock or damage. Avoid using the charger in dusty places.

15. Stop charging if any abnormality is detected.

- If you detect excessive heat or any other abnormality while charging, stop immediately and have the charger repaired.

16. Store the charger and battery correctly.

- Store the charger and the storage battery in a dry place out of the reach of children and where the temperature

does not exceed 40

͠

. Never store under the eaves of a house, for example, where rain might get in.

Deterioration of the electrical insulation can result in electric shock.

17. Charge once every three months.

- It is recommended that even if you do not use them, lithium-ion batteries should be charged about once every three

months in order to prevent over-discharge.

18. Do not store fully-charged lithium-ion batteries for long periods of time.

- If you need to store the battery for a long period of time, store at room temperature at about 50% of the battery's capacity.

WARNING

Fig. 1

Plug

Ventilation hole

Green lamp

Red lamp

Charger

Storage battery
mounting socket

Power cord

Summary of Contents for RF20SC

Page 1: ...SB RF20SC RF20S RT20S thoroughly before using the machine Keep the manuals where the operator can refer to them whenever necessary 1 Safety Considerations 1 Precautions WARNING 1 Use the tool only for its designated purpose Using the tool for any purpose other than flaring flanging pipes will not only damage the tool and or the motor but could also lead to accident or injury 2 Ensure you use the c...

Page 2: ...ither the storage battery or the charger The charger and the storage battery houses condensers and electronic parts Disassembly could result in electric shock or damage to the charger never try to disassemble them 12 Never short circuit the charger The lithium ion battery used with this unit has an extremely low internal resistance If short circuited there may be a surge in the current resulting i...

Page 3: ...ture of the battery is outside the acceptable range Below 0 or above 50 On On Unable to charge Defective battery etc Mark 80 Table 2 Storage battery mounting socket Hold the main unit firmly and remove the battery Recharge the battery once the flaring tool starts to loose power If the battery is completely drained it may not be possible to fully recharge it resulting in shortened battery life CAUT...

Page 4: ...y is outside the acceptable range for charging Allow the temperature to return to within the acceptable range 0 50 The red lamp on the charger flashes slowly The battery is damaged Replace the battery The red and green lamps are on at at the same time Problem Cause Remedy Table 3 5 Troubleshooting 6 Servicing and Repairs This machine is produced with great precision therefore should the machine fa...

Reviews: