REWIRE SECURITY DB3 User Manual Download Page 84

Page: 84 / 122

GPRS content ac

ivation

(ID=1240)

9.4.10 Backup Server Protocol (ID=1249)

Parameter defines GPRS data transport protocol for backup server. Module can
use TCP or UDP transport protocol to send data to server. For TCP protocol
value is 0, for UDP protocol value is 1.

Minimum
value

Maximum
value

Recommended

value

Goes with (depends on)
parameters

Value
type

GPRS content ac

ivation

(ID=1240)

9.4.11 SMS Login (ID=1252)

User login is used to ensure module security. Used in every SMS that is sent to
the device. Example: ba321.

Minimum
value

Maximum
value

Recommended

value

Goes with (depends on)
parameters

Value
type

Empty

5 char

SMS Password (ID=1253)

S8[5]

9.4.12 SMS Password (ID=1253)

User password is used to ensure module security. Used in every SMS that is
sent to the device.

Example

: ab123.

Minimum
value

Maximum
value

Recommended

value

Goes with (depends on)
parameters

Value
type

Empty

5 char

S8[5]

Summary of Contents for DB3



























































































































Search results

Summary of Contents for DB3

Reviews:

REWIRE SECURITY DB3, User Manual, Page: 84 / 122

Search results

Summary of Contents for DB3

Reviews: