Reverie 3E Power Base Owner'S Manual And Reference Manual Download Page 13

CUSTOMER SERVICE: 800-973-8374

[email protected]

13

Frame Assembly Instructions

Headboard Bracket Installation

STEP 1

STEP 2

Install the headboard brackets to the power base. 

Place one bracket on the left-hand side of the 

base and one bracket on the right-hand side of 

the base.

1.  Use the hand control to raise the head of the 

base in order to gain access to the power 

base.

2.  Bolt the Leg Clamp Bracket (A) to the leg 

using the headboard bracket bolts (D), and 

the 5/16” lock nut (G).

3.  Bolt the inner Headboard Bracket (B) to the 

Leg Clamp Bracket (A) using the Headboard 

Bracket Bolts (E), the 5/16” washer (F), and 

the 5/16” lock nut (G).

4.  Place the open side of the outer headboard 

bracket (C) onto the exposed square tube of 

the inner head board bracket (B). This will 

create a tight fit between (B) and (C). Place a 

Headboard Bracket Bolt (E) with a 5/16 Inch 

Washer (F) through the Outer Headboard 

Bracket (C) and into the Inner Headboard 

Bracket (B). Use a 5/16 Inch Washer (F) and 

5/16 Inch Locking Nut (G) and hand tighten to 

allow for adjustment. Repeat same procedure 

for opposing side of the power base.

 

5.  Ensure the headboard bracket is assembled 

a distance of 1.5 (38.1 mm) to 2 inches 

(50.8 mm) between the edge of the 

power base and the headboard bracket 

assemblies.

6.  Firmly tighten the headboard bolts (not 

included) to the end of the headboard 

bracket assembly.

7.  Measure the distance of the center to center 

mounting holes in the headboard.

8.  Measure the distance of the center to center 

mounting holes in the headboard bracket 

assemblies.

9.  If the headboard brackets require 

adjustments, loosen the bolts that are 

holding the outer headboard brackets and 

move them to the necessary distance. 

Reinstall the bolts and firmly tighten.

Place your mattress on top of your power base.

Typical Reverie 

3E™

 Power Base 

is 

Headboard installation

 now complete. If the 

base is equipped with a programmable setting 

or options, refer to the Hand Control Guide for 

more information.

G

A

D

I

I

H

D

A

G

B C

E

H

F

F

A

B

B

A

C F

E

G

E

Summary of Contents for 3E Power Base





























Reviews: