REVENTON S1-3S Technical Documentation Manual Download Page 2

Page: 2 / 16

1.INTRODUCTION

1.1 PRECAUTIONS

1.2 TRANSPORT

1.3 PACKAGE CONTENT

1.4 USE

2. DEVICE CHARACTERISTICS

2.1 CONSTRUCTION AND PRINCIPLE OF OPERATION

2.2 DEVICE DIMENSIONS

2.3 DEVICE TECHNICAL DATA

3. ASSEMBLY

3.1 GENERAL PRINCIPLES

3.2 ROTATING MOUNTING BRACKET

3.3 FIXED HOLDERS

4. INSTALLATION INSTRUCTIONS

4.1 CONNECTION OF THE DEVICE TO THE HYDAULIC SYSTEM

4.2 CONNECTION OF THE DEIVCE TO THE ELECTRICAL SYSTEM

5. PRECAUTIONS & WARNINGS
6. CONTROLS
7. CONNECTION SCHEMES
8. TERMS OF WARRANTY

INTRODUCTION

Thank you very much for purchasing air water heater S-3S.

We would like

to congratulate you on excellent choice. Please read and keep this manual.

1.1

PRECAUTIONS

The buyer and the user of the air water heater Reventon Group brand should
read  carefully  the  following  instructions  and  proceed  to  the  content
recommendations.    Proceeding  due  to  the  following  instruction  guarantees
the  correct  usage  and  safety.  In  case  of  any  doubts  please  contact  directly
Reventon  Group  sp.  z  o.  o.  [Ltd.].  The  producer  reserves  the  rights  to  make
changes  to  the  technical  documentation  without  previous  notice.  Reventon
Group  sp.  z  o.  o.  [Ltd.]  is  not  responsible  for  the  damages  which  occur  due
to  improper  installation,  not  keeping  the  device  in  repair  or  using  the  device
out of line. The installation should be carried out by the professional installers,
who possess the qualifications to install these types of devices. The installers
are responsible for making the installation as instructed in the technical data.
In  case  of  unserviceable  please  plug  out  the  device  and  contact
with  the  authorizedfor  repair  person  or  the  supplier.  During  the  installation,
use,  service  and  periodical  inspections  all  regulations  and  safety  rules
must be followed.

1.2 TRANSPORT

During the acceptance of goods, it is needed to check the device to exclude
any damages. During the transport, it is needed to use the proper equipment,
it is necessary to carry the device by two people. In case of any damages please fill
in the damage report in presence of the supplier.

1.3

PACKAGE CONTENT

- h

eater

- o

peration and maintenance manual and warranty card

1.4

USE

Heating  devices  Reventon  Group  S  series  are  used  to  heat  spaces  such  as:
production  halls,  warehouses,  commercial  room,  service  spaces,  garages,
workshops,  greenhouses,  tents,  shops,  malls,  shopping  malls  etc.    However,
heating  devices  should  not  be  used  in  corrosive  environments  for  aluminum,
copper  and  steel  as  well  as  in  highly  dusty  environments  (above  0.3  g/m³).
The  devices  should  not  be  installed  in  rooms  where  they  would  be  exposed
to high humidity or direct contact with water.

DEVICE CHARACTERISTICS

2.1

CONSTRUCTION AND PRINCIPLE OF OPERATION

Casing:

made of galvanized steel casing, powder painted in RAL 9005 color.

Air stators:

made of galvanized steel casing, powder painted in RAL 7048 color.

It is possible to adjust manually the air stators to achieve the needed direction
of the air flow.

Heating coil:

made of copper and aluminum. Supplied by distribution working

fluid, which circulates through the coil and releases heat to the air. The coil
has the following technical parameters: the maximum temperature
of the heating factor is 120°C; maximum pressure 1

6 MPa; headers diameter ¾”.

Depending on dimensions of the device the heaters are equipped
with 1, 2 or

3-row heating coils.

ENG

TECHNICAL DOCUMENTATION

Axial blowing fan:

made of galvanized steel. The objective of the fan is to ensure

air flow through the exchanger. It has a single-phase, three speed motor
with the following parameters: protection degree IP54, rate current 0.2 - 0.84 A
(depending on model and operating mode). Model S1-3S has fan with diameter
300 mm. Models S2-3S and S3-3S have fans with diameter 350 mm and S4-3S
has fan with diameter 400 mm.

Rotating mounting bracket (optional equipment):

enables the device

to be installed in several configurations (depending on the requirements)
and the unit to be rotated in a horizontal plane.

Fixed holders (optional equipment):

made of steel, element for mounting

the device on a wall or ceiling. Solid and durable construction, possible
to assemble device in parallel on the angle 60° and 45°.

2.2

DEVICE DIMENSIONS

- S4-3S:

: 660 mm

: 696 mm

: 384 mm