background image

E-9

ENGLISH

PART II PRODUCT INFORMATION

The sixe stages of air cleaning

1. The Pre-filter traps large dust particles.
2. The two-stage electrostatic precipitator (Electronic cell) captures airborne particles, as small as 0.01 microns. In the ionizing
section of the electronic cell, billions of microscopic particles become electrically charged as they pass through the powerful
electric field. The collector plates immediately attract and collect these charged dust and dirt particles.
3. The activated carbon filter absorbs and reduces odors, chemicals and gases, removes tobacco smoke, the smell of food and 
other odors.
4. The UV sterilization chamber kills bacteria and viral microorganisms such as influenza, TB and Legionnaire's Disease as well 
as other harmful contaminants.
5. When UV light hits the photo catalytic filter; it creates e- and h+, which have an excellent effect in the decomposition of odors.

Standby Power

In order to operate the electrical 
circuits while the power plug is 
inserted in the wall outlet, this 
product consumes about 4.6W of
standby power. For energy 
conservation, unplug the power cord 
when the unit is not in use.

Specifications

Model No.

Power Requirement

Rated Power

Fan Motor 

Fan Speed

Noise Level

Negative Ion

UV Lamp

Cord Length

Dimensions

Weight

RespirAide 300T

120V, 60Hz, 0.71A

83W

120V, 60Hz

H-435m

3

/h, M-340m

3

/h, L-240m

3

/h

<55dB

3x10

6

pcs/cc

6W

2.5m (8.3 ft)

H82.8cmxW47.8cmxD23.2cm

27.7kg

AC120V, 60Hz

Interlock switch

Interlock switch

White

White

Y. green

Y. green

Black

White

Fan motor

UV lamp and ballast

White

White

Negative ion 
generator

Electronic cell

 Collector
(2nd stage)

Ionizer
(1st stage)

Black

Red

Red

Red

Remote control 
receiver

DISPLAY CIRCUIT BOARD

Transformer

Red

Red

Red

Blue

Black

Yellow

JZ12

JZ5

JZ5

JZ4

JZ9

JZ13

JZ3

JZ8

JZ7

JZ1

JZ2

JZ6

JZ11 JZ10

Black(-)

Red(+)

MAIN CIRCUIT BOARD

Y. Green

Pink white

Odor sensor

Pink white

Pink white

H

M

L

C

Power supply
(HVG)

Fuse

Green

Power cord
socket

Transformer

Blue

Blue

 18V 

F1

Reset button

Wiring schematic 

Summary of Contents for 300T























































Reviews: