RespirAide 300T Service Manual Download Page 30 | Manualshive

Page: 30 / 54

background image

PART III

IMPORTANT PARTS - DISPLAY CIRCUIT BOARD

E-30

ENGLISH

DISPLAY CIRCUIT BOARD

1. After take off the front
panel remove 4 screws on
the upper plate.

3. Lift up the plastic top cover
from the top back hooks.

4. Unplug the display circuit
board wires from display circuit
board.

5. Remove a screw on the odor
sensor circuit board.

2. Unscrew 3 screws on the
plastic top cover.

Replace display circuit board

The display circuit board is also seldom broken down. If you confirm that the display circuit board is broken, you will follow
the below steps and install it correctly through the reverse operation.
1. Stop the operation and unplug the power cord.
2. Take off the front panel from the unit.

Display circuit
board wire

Remote signal receiver circuit
board wire

Odor sensor circuit
board wire

Display circuit board

The display circuit board is one of the most important parts of the unit. It is located inside the plastic top cover. The
circuit board is connected to the main circuit board by display circuit board wire. If the display circuit board wire
connections are loosened, or circuit boards are broken there will no display lights or incorrect display indicator lights on
the display panel. Pressing any buttons on the control panel will control the main circuit board through the display
circuit board wire for the unit to carry out the desired functions.

«
...
28
29
30
31
32
...
»

Summary of Contents for 300T























































Reviews:

No comments

Related manuals for 300T

Brand: Haier Pages: 22

Brand: Haier Group Pages: 28

Brand: Samsung Pages: 20

Brand: Samsung Pages: 16

Brand: Panasonic Pages: 122

Brand: Fakir Pages: 28

Brand: Fakir Pages: 32

Brand: Fakir Pages: 47

Brand: Daikin Pages: 7

Brand: Daikin Pages: 6

Brand: Daikin Pages: 24

Brand: Daikin Pages: 28

Brand: Daikin Pages: 34

Brand: Daikin Pages: 44

Brand: Daikin Pages: 44

Brand: Daikin Pages: 13

Brand: Daikin Pages: 22

Brand: Daikin Pages: 134

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands