background image

DCN: 141-00940-09  11/02/07 

 

Remote Sensors  

 
The TS16 Wall Display Unit has a remote sensor terminal block, J2, on the base for connection of a 
remote temperature sensor.   Without any remote sensor attached, the WDU uses the internal sensor for 
the current temperature information.  When a remote sensor is attached, the WDU will detect it 

automatically

 and will use the remote sensor(s) according to its address selection.  Modes of operation are 

as follows: 
 
Address 1:  Use the remote sensor instead of internal sensor.  (becomes C1 in the calibration setup). 
Address 2:  Average remote sensor 2 with internal sensor or remote sensor 1. (C2 in the calibration setup)          
Address 3:  Not used with the TS16   
  
 

Table of Remote Sensor Functions and Sensor Addresses 

 

Function 

Remote Addr 1 

Remote Addr 2 

Remote Addr 3 

Use internal sensor only 

No 

No 

Not used 

Use remote sensor only 

Yes 

No 

with TS16 

Average internal and one remote 

No 

Yes 

  

Average two remotes (only 2) 

Yes 

Yes 

  

 

When averaging sensors are used, the 

average

 temperature is displayed on the WDU and reported to the 

HVAC control unit.  You cannot view an individual remote averaging sensor temperatures as the main 
thermostat display or report individual sensor temperatures on the communication port.  However, you can 
check the individual sensor temperatures by going to the calibration setup menu and selecting the sensor 
address.  You can view the outside temperature by pressing both the UP/DOWN buttons simultaneously. 
 
 

WDU Error Displays 

 

“CF” Error Display 

 
If the WDU is not properly wired or if communications to the Control Unit is interrupted, the LCD display will 
display “CF” to denote communications failure. Momentary display of “CF” caused by bad or lost data, will 
clear automatically when data communications is restored. 
 
 If the “CF” display stays on, check wiring for problems.  A continuous “CF” display may indicate a problem 
with the Control Unit or the WDU itself.  
 

 “SF” Error Display 

 
If the WDU detects that a sensor is not responding, it will display “SF”.  In most cases this will clear itself 
when communications is restored to the sensor.  A continuous “SF” display may indicate a problem with the 
wiring or the WDU itself.   Check wiring and replace the WDU as needed. 
 

“-- --“ Error Display 

This denotes that the temperature is invalid.  Can appear if you select outside temperature and no remote 
sensor is attached or if an error in temperature is sensed momentarily by the WDU.  Clears automatically 
when a valid temperature is read.

Summary of Contents for TXB16























Reviews: