manualshive.com logo in svg

Renesas SH7781, Hardware Manual

The Renesas SH7781 Hardware Manual is a comprehensive guide designed to assist users in understanding the technical aspects and capabilities of the product. Available for free download from our website, this manual provides essential information for optimizing the performance and functionality of the Renesas SH7781.

Share
Download
background image

19.   Display Unit (DU) 

Rev.1.00  Jan. 10, 2008  Page 843 of 1658 

REJ09B0261-0100 

 

Bit Bit 

Name 

Initial 
Value R/W 

Internal 
Update Description 

9 DRES 

1 R/W 

None 

Display 

Reset 

8 DEN 0 R/W 

Yes 

Display 

Enable 

00: Starts display synchronization operation. 

In the case of a register not yet set, 
unexpected operation may occur; hence 
DRES should be set to 0 after setting all the 
registers in the display unit (DU). 
When DEN = 0, the display data is the value 
set in the display-off output register (DOOR).

01: Starts display synchronization operation. 

In the case of a register not yet set, 
unexpected operation may occur; hence 
DRES and DEN should be set to 0 and 1 
respectively after setting all the registers in 
the display unit (DU). 
When DEN = 1, the display data is the value 
stored in memory from the next frame. 

10: Halts display and synchronization operation.

Halts display operation and synchronization 
operation. Except for the following bits in 
DSSR, register settings are held. 
For these settings, operation is as follows. 

1. All display data output is 0. 

2. The following bits in DSSR are cleared to 

0. 

⎯

 

TV sync signal error flag (TVR) 

⎯

 

Frame flag (FRM) 

⎯

 

Vertical blanking flag (VBK) 

⎯

 

Raster interrupt flag (RINT) 

⎯

 

Horizontal blanking flag (HBK) 

3. The 

HSYNC

, 

VSYNC

, ODDF pins are input 

pins. 

However, when the ODPM bit in DSMR is 1, the 
ODDF pin output is clamped. 

11: Setting prohibited 

 

Summary of Contents for SH7781





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7781

Z3 Technology Z3-DM8168-PCI-RPS Manual preview
Z3-DM8168-PCI-RPS
Brand: Z3 Technology Pages: 20
Z3 Technology Z3-DM8107-SDI2-RPS User Manual preview
Z3-DM8107-SDI2-RPS
Brand: Z3 Technology Pages: 75
Z-Wave USB Dongle User Manual preview
USB Dongle
Brand: Z-Wave Pages: 13
D-Link AirPlus XtremeG Ethernet-to-Wireless Bridge... Manual preview
AirPlus XtremeG Ethernet-to-Wireless Bridge...
Brand: D-Link Pages: 31
Maxim DS5001FP Specification Sheet preview
DS5001FP
Brand: Maxim Pages: 26
Broadcom Brocade X6-8 Director Hardware Installation Manual preview
Brocade X6-8 Director
Brand: Broadcom Pages: 207
Telit Wireless Solutions HE922-3GR Hardware User'S Manual preview
HE922-3GR
Brand: Telit Wireless Solutions Pages: 113
Matrox Millennium P650 User Manual preview
Millennium P650
Brand: Matrox Pages: 54
XNET INS2000 Install Manual preview
INS2000
Brand: XNET Pages: 17
ICP DAS USA PDS-734D Quick Start Manual preview
PDS-734D
Brand: ICP DAS USA Pages: 8
ADC HiGain H2TU-R-402 List 7A Quick Installation preview
HiGain H2TU-R-402 List 7A
Brand: ADC Pages: 7
Renesas H8S/2633 User Manual preview
H8S/2633
Brand: Renesas Pages: 28
Quantum QWCM Installation Manual preview
QWCM
Brand: Quantum Pages: 7
ARTERY AT32F421 Series Reference Manual preview
AT32F421 Series
Brand: ARTERY Pages: 337
XtendLan XL-HCW224C User Manual preview
XL-HCW224C
Brand: XtendLan Pages: 52
QTech QSW-2900 User Manual preview
QSW-2900
Brand: QTech Pages: 406
INNOSILICON T3-43T User Manual preview
T3-43T
Brand: INNOSILICON Pages: 11
NZXT RESPIRE T40 Manual preview
RESPIRE T40
Brand: NZXT Pages: 2

Brands by name

Popular brands

Load more brands