Renesas RTE7702500EAB00000J User Manual Download

Page: 41 / 63

Emulation Adapter

System Configuration and Setup

R20UT5180EJ0110 Rev. 1.10

Page 31 of 63

Sep.12.22

3.2.2

Settings for Use as an Emulation Board

Table 3-4 shows a list of the recommended settings of the emulation adapter for this system

configuration.

Table 3-4 Recommended Settings for Use as an Emulation Board

Item

Description

Debug chip: IC1

Set an option byte. Refer to section 4.1.

Connector for external tracing: CN1 When an emulator is in use: Connect the cable for the emulator, the 14-

pin to 46-pin conversion adapter, or the 34-pin to 46-pin conversion

adapter.
When an emulator is not in use: Leave the connector open-circuit.

Power-supply connector: CN3

Set up a +5-V supply through the attached power-supply cable.
If you are using the IE850A, power can be supplied from the power-

supply cable attached to the IE850A.

Clock socket: X1

A resonator is mounted (20 MHz as shipped).
When you are evaluating the emulation adapter with a different

frequency or with a crystal oscillator as the main oscillator, change the

resonator or exchange it for an oscillator.

Jumper block: JP5 (VDD_SEL)

1-2 short-circuit (default)

Jumper block: JP10 (AURORES)

1-2 short-circuit (default)

Jumper block: JP11

(EXAURORES)

1-2 short-circuit (default)

Jumper block: JP14 (TRST_SEL)

1-2 short-circuit (default)

Jumper block: JP2 (FLMD0)

1-2 short-circuit (default)

Jumper block: JP12 (FLMD0_SEL)

1-2 short-circuit (default)

Jumper block: JP9 (FLMD1)

2-3 short-circuit (default)

Jumper block: JP13 (FLMD1_SEL)

1-2 short-circuit (default)

Jumper block: JP15 (RES_SEL)

1-2 short-circuit (default)

Jumper block: JP1 (VDD_EMU)

Short-circuit (default)

Jumper block: JP4 (EMUVDD)

1-2 short-circuit (default)

Jumper block: JP6

(EMUVDD_SEL)

1-2 short-circuit (default)

Jumper block: JP3 (EMUVCC)

Short-circuit (default)

Jumper block: JP7 (SBMD)

Select the connection on this jumper block according to the emulation

mode to be used. Refer to (19) in section 2.1.

Jumper block: JP8 (AWOVCL)

Select the connection on this jumper block according to the emulation

mode to be used. Refer to (20) in section 2.1.

Interfaces for the exchange

adapter: CN10 and CN11

Connect these connectors to the base board.

Summary of Contents for RTE7702500EAB00000J
































































Search results

Summary of Contents for RTE7702500EAB00000J

Reviews:

Related manuals for RTE7702500EAB00000J

Brands by name

Popular brands

Renesas RTE7702500EAB00000J, User Manual

Search results

Summary of Contents for RTE7702500EAB00000J

Reviews:

Related manuals for RTE7702500EAB00000J

Brands by name

Popular brands