background image

User’s Manual 

R12UT0012EJ0100  Rev.1.00 

 

Page  1  of 32 

20.10.2020 

 

RL78/G1F Motor Driver Board GB01 

User's Manual 

For Your Safety 

Be sure to read this manual before using the RL78/G1F Motor Driver Board GB01 (P13130-D1-003) (this 

product). 

 

Follow the indications in this manual when using the product. 

 

Keep this manual near the product so you can refer to it whenever necessary. 

 

Transfer or sale of the product to third parties is prohibited without written approval. 

 

The purchaser or importer of the product is responsible for ensuring compliance with local regulations. In 

addition, the customer is responsible for ensuring that the product is handled correctly and safely, in 

accordance with the laws of the customer’s country (region). 

 

The manual for the product, and specification (the documents) are the tool that was developed for the 

function and performance evaluation of Renesas Electronics semiconductor device (Renesas Electronics 

device) mounted on the product, and not guarantee the same quality, function and performance.     

 

By purchasing the product or downloading the documents from Renesas Electronics website, the support 

services provided from Renesas Electronics is not guaranteed. 

 

All information contained in this manual represents information on products at the time of publication of 

this manual. Please note that the product data, specification, sales offices, contents of website, address, 

etc., are subject to change by Renesas Electronics Corporation without notice due to product 

improvements or other reasons. Please confirm the latest information on Renesas Electronics website. 

 
 
In this manual items related to the safe use of the product are indicated as described below. 

  The degree of injury to persons or damage to property that could result if the designated content in this 

manual is not followed is indicated as follows. 

  Danger 

Indicates content that, if not followed, could result in death or serious 

injury*

1

 to the user, and which is highly urgent. 

  Warning 

Indicates content that, if not followed, could result in death or serious 

injury to the user. 

  Caution 

Indicates content that, if not followed, could result in injury*

2

 to persons or 

physical damage.*

3

 

Note 1.  Serious injury refers to conditions resulting in persistent after-effects and for which treatment would 

necessitate hospitalization or regular hospital visits, such as loss or impairment of eyesight, burns 

(high- or low-temperature), electric shock, bone fracture, or poisoning. 

Note 2.  Injury refers to conditions for which treatment would necessitate hospitalization or regular hospital 

visits. 

Note 3.  Physical damage refers to damage affecting the wider surroundings, such as the user’s home or 

property. 

 
 

 

 

R12UT0012EJ0100 

Rev.1.00 

20.10.2020 

 

Summary of Contents for RL78/G1F




































Reviews: