Renesas H8S/2214 Series User Manual Download Page 16 | Manualshive

Page: 16 / 22

background image

2.3

Recommended Dimensions for User System Mount Pad

Figure 7 shows the recommended dimensions for the mount pad (footprint) for the user system with
an IC socket for an TBP-112 package (CSPACK112A1110H01: socket (manufactured by Tokyo
Eletech Corporation). Note that the dimensions in figure 7 are somewhat different from those of the
actual chip's mount pad.

Figure 7 Recommended Dimensions for Mount Pad

12

«
...
14
15
16
17
18
...
»

Summary of Contents for H8S/2214 Series























Reviews:

No comments

Related manuals for H8S/2214 Series

Ray 3 Plus Client

Brand: Sun Microsystems Pages: 6

Brand: National Instruments Pages: 85

Brand: Belkin Pages: 72

MegaRAID SCSI 320-2X

Brand: LSI Pages: 4

Brand: VCS Pages: 118

Brand: JETWAY Pages: 55

Brand: Dantel Pages: 62

Brand: Cypress Semiconductor Pages: 28

CP 040 RS422/485

Brand: YASKAWA Pages: 87

Brand: Goobay Pages: 28

Brand: COMBA Pages: 57

Scalable Multi-Graphic Videowall Processors MGP 464W Series

Brand: Extron electronics Pages: 2

Brand: Korg Pages: 647

Brand: Huawei Pages: 2

FusionModule 500

Brand: Huawei Pages: 29

Brand: Huawei Pages: 3

eSight V200R003C00

Brand: Huawei Pages: 28

Brand: Huawei Pages: 49

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands