( 22 / 84 )
* Please keep the M3062NT3-RPD-E's packing box and cushion material in your place for reuse
at a later time when sending your product for repair or other purposes. Always use these packing
box and cushion material when transporting this product.
* If any of these items are missing or found faulty, please contact your local distributor.
* If there is any question or doubt about the packaged product, contact your local distributor.
* For purchasing the IC61-1004-051 or for technical information, contact Yamaichi Electronics
Co., Ltd.
2.2 Other Tool Products Required for Development
To bring forward programs development on an M16C/62 Group M16C/62N and M16C/30 Group
M16C/30L, the products listed below are necessary in addition to those contained package above. Get
them separately.
Table 2.2 Other tool products
* To purchase these products, contact your local distributor.
Chapter 2. Preparation
2.1 Package Components
The M3062NT3-RPD-E package consists of the following items. When unpacking, check to see if
your M3062NT3-RPD-E contains all of these items.
Table 2.1 Package components
Emulator main unit
Emulator debugger
Converter board
PC4701 (excluding PC4701L and PC4700L)
M3T-PD30
For 80-pin 0.65-mm-pitch QFP (80P6S-A):
M3T-100LCC-DMS + M3T-FLX- M3T-FLX80QSB
M3T-100LCC-DMS + M3T-FLX- M3T-DIRECT80S
For 100-pin 0.65-mm-pitch QFP (100P6S-A):
M3T-100LCC-DMS + M3T-DIRECT100S
M3T-100LCC-DMS + M3T-DUMMY100S
M3T-100LCC-DMS + M3T-FLX-100NRB
For 100-pin 0.5-mm-pitch LQFP (100P6Q-A):
M3T-F160-100NSD
M3T-100LCC-QSD
M3T-100LCC-DMS + M3T-FLX-100NSD
For 100-pin 0.4-mm-pitch TQFP (100PFB-A):
M3T-F160-100NSE
Required according to the foot pattern of the target system (see "3.8
Connecting the Target System" on page 41)
Item
M3062NT3-RPD-E emulation pod main unit
FLX120-RPD flexible cable for connecting PC4701
M3T-F160T3-PRB converter board for M3T-FLX160C (preinstalled)
M30800T-PTC converter board for 100-pin 0.65-mm-pitch QFP
IC61-1004-051 100-pin 0.65-mm-pitch LCC socket (made by Yamaichi Electronics Co., Ltd.)
OSC-3 16 MHz oscillator circuit board for main clock (preinstalled)
OSC-2 oscillator circuit board for main clock (bare board)
Resistor arrays for pulling up ports P0 to P5 (51 k
Ω
)
Hardware tool user registration FAX sheet
Hardware tool user registration FAX sheet (Japanese)
M3062NT3-RPD-E User's Manual (This manual)
M3062NT3-RPD-E User's Manual (Japanese)
Quantity
1
1
1
1
1
1
1
6
1
1
1
1
Summary of Contents for Emulation Pod M3062NT3-RPD-E
