Renesas DA9213 User Manual Download Page 3

Page: 3 / 38

UM-PM-029

DA9213, DA9214, and DA9215 Performance
Boards

User Manual

Revision 2.0

25-Feb-2022

CFR0012

3 of 37

Figure 16: DVC Transition ................................................................................................................... 24

Figure 17: Buck Tab CONTROL_A Register Field .............................................................................. 24

Figure 18: GPIO Port Voltage Control ................................................................................................. 25

Figure 19: Port Control of the Buck Output Voltage ............................................................................ 25

Figure 20: ATSAM3U µ-Controller for USB-I

C bridge ....................................................................... 30

Figure 21: Mini USB Input and Internal Rails Generation ................................................................... 31

Figure 22: Control and I/O Signals Headers ....................................................................................... 31

Figure 23: GPIOs Control Jumpers ..................................................................................................... 32

Figure 24: GPIOs Control Schematic .................................................................................................. 32

Figure 25: History Log ......................................................................................................................... 35

Tables

Table 1: DA9213 Performance Board (227-02-A) Links Description .................................................. 27

Table 2: DA9214 Performance Board (227-04-D) Links Description .................................................. 28

Table 3: DA9215 Performance Board (227-07-B) Links Description .................................................. 29

Summary of Contents for DA9213







































Search results

Summary of Contents for DA9213

Reviews:

Related manuals for DA9213

Brands by name

Popular brands

Renesas DA9213, User Manual

Search results

Summary of Contents for DA9213

Reviews:

Related manuals for DA9213

Brands by name

Popular brands