eng eng
Leaking battery fluid can cause skin irritation and burns. Rinse off immediately
with water in case of contact. Also consult a doctor if the fluid gets into the eyes.
●
Observe the safety instructions on the battery and the rapid charger.
●
Keep unused batteries away from paper clips, coins, keys, nails, screws
or other small metal objects which could cause bridging of the contacts.
There is a risk of explosion and fire due to short-circuiting.
●
Remove the battery before stowing/storing the power tool for long periods
of time. Protect the battery contacts against shortcircuiting, e.g. with a cap. This
reduces the risk of fluids escaping from the batteries.
●
Do not throw defective batteries in the normal household waste. Hand the
defective batteries over to an authorised REMS contract service workshop or a
recognised disposal company. Observe the national regulations. See also page
6. Disposal.
●
Keep batteries out of reach of children. Batteries can be life threatening if
swallowed, seek medical assistance immediately.
●
Avoid contact with leaking batteries. Leaking fluid can cause skin irritation
and burns. Rinse off immediately with water in case of contact. Also consult a
doctor if the fluid gets into the eyes.
●
Take the batteries out of the power tool when they are empty. This reduces
the risk of fluids escaping from the batteries.
●
Never recharge the non-rechargeable batteries, open them, throw them on
fires or create a short-circuit. The batteries can cause fires and burst. There
is a risk of injury.
Explanation of symbols
WARNING
Danger with a medium degree of risk which could result in
death or severe injury (irreversible) if not heeded.
CAUTION
Danger with a low degree of risk which could result in minor
injury (reversible) if not heeded.
NOTICE
Material damage, no safety note! No danger of injury.
Read the operating manual before starting
Use eye protection
Use ear protection
Electrical device complies with protection class II
Environmental friendly disposal
CE conformity mark
1. Technical Data
Intended use
WARNING
REMS radial presses are intended for the purpose of making press joints of all
common pressfitting systems.
REMS cropping tongs are intended for the purpose of cropping threaded bars up to
the strength class 4.8 (400 N/mm²).
REMS cable shears are intended for the purpose of cropping electric cables
≤ 300 mm² (Ø 30 mm).
REMS axial presses are intended for the purpose of making compression sleeve
connections.
REMS pipe expanders are intended for the purpose of expanding and calibrating
pipes.
REMS batteries are intended for supplying energy to the REMS cordless drive units
and the REMS cordless LED lamp. Note voltage of the batteries.
Rapid chargers are intended for charging the REMS batteries.
All other uses are not for the intended purpose and are prohibited.
1.1. Scope of Supply
Electrical radial presses/pipe expanders: Drive unit, instruction manual, sheet
steel case
Cordless presses/pipe expanders: Drive unit, Li-Ion battery, rapid charger,
instruction manual, sheet steel case
1.2. Article numbers
REMS Power-Press SE drive unit
572101
REMS Power-Press drive unit
577001
REMS Power-Press ACC drive unit
577000
REMS Power-Press XL ACC
579000
REMS Mini-Press ACC drive unit Li-Ion
578001
REMS Mini-Press 22 V ACC drive unit Li-Ion
578002
REMS Akku-Press drive unit Li-Ion
571003
REMS Akku-Press ACC drive unit Li-Ion
571004
REMS Ax-Press 25 ACC drive unit Li-Ion
573003
REMS Ax-Press 25 L ACC drive unit Li-Ion
573004
REMS Ax-Press 30 drive unit Li-Ion
573008
REMS Ax-Press 40 drive unit Li-Ion
573006
REMS Akku-Ex-Press Cu ACC drive unit Li-Ion
575006
REMS Akku-Ex-Press P drive unit Li-Ion
575009
REMS Akku-Ex-Press P ACC drive unit Li-Ion
575008
REMS Akku-Ex-Press Q & E ACC drive unit Li-Ion
575005
REMS Power-Ex-Press Q & E ACC drive unit
575007
Expanding device 6 – 40 mm, ½ – 1½" 575100
Expanding device 54 – 63 mm, 2"
575101
REMS battery Li-Ion 14.4 V, 1.5 Ah
571545
REMS battery Li-Ion 14.4 V, 3.0 Ah
571555
REMS battery Li-Ion 21.6 V, 1.5 Ah
571570
REMS battery Li-Ion 21.6 V, 2.5 Ah
571571
Rapid charger Li-Ion/Ni-Cd 230 V
571560
Rapid charger Li-Ion 230 V
571575
Voltage supply Li-Ion 230 V, instead of 14.4 V batteries
571565
Sheet steel case, REMS Power-Press SE
570280
Sheet steel case, REMS Power-Press
570280
Sheet steel case, REMS Power-Press ACC
570280
Transport box XL REMS Power-Press XL ACC 579240
Sheet steel case, REMS Mini-Press ACC / Mini-Press 22 V ACC
578290
Sheet steel case, REMS Akku-Press / REMS Akku-Press ACC
571290
Sheet steel case, REMS Ax-Press 30 / Ax-Press 40
573282
Sheet steel case, REMS Akku-Ex-Press Q & E
578290
Sheet steel case, REMS Ax-Press 25 ACC / Ax-Press 25 L ACC
578290
Sheet steel case, REMS Akku-Ex-Press Cu ACC
578290
Sheet steel case, REMS Akku-Ex-Press P / Akku-Ex-Press P ACC 578290
Sheet steel case, Combi Set REMS Ax-Press 25 ACC
and Akku-Ex-Press P ACC
573284
REMS CleanM
140119
1.3. Capacity
REMS Mini-Press ACC / Mini-Press 22 V ACC Radial press
for making press joints in all standard press fitting systems
on steel pipes, stainless steel pipes, copper pipes, plastic
pipes, composite pipes
Ø 10 – 40 mm
Ø
⅜ – 1¼"
Radial presses REMS Power-Press / Power-Press ACC /
Power-Press XL ACC and REMS Akku-Press / Akku-Press ACC
for producing press fittings of all common
press fitting systems on steel pipes, stainless steel
pipes, copper pipes, plastic tubes, composite tubes
Ø 10 – 108 mm
Ø
⅜ – 4"
Axial presses for making compression sleeve joints (sliding
sleeve joints) on stainless steel pipes, steel pipes, copper
pipes, plastic pipes, composite pipes
Ø 12 – 40 mm
REMS Akku-Ex-Press Q & E ACC for expanding of
pipes/coil for the system Uponor Quick & Easy
Ø 16 – 40 mm
Ø ⅜ – 1½"
REMS Power-Ex-Press Q & E ACC for expanding of
pipes/coil for the System Uponor Quick & Easy
Ø 16 – 63 mm
Ø
½ – 2"
REMS Akku-Ex-Press Cu ACC for widening and calibrating
soft copper pipes, soft aluminium pipes, soft precision steel
pipes, soft stainless steel pipes
Ø 8 – 42 mm
Ø ⅜ – 1¾"
REMS Akku-Ex-Press P and REMS Akku-Ex-Press P ACC
for widening plastic pipes, composite pipes
Ø 12 – 40 mm
Operating temperature range
REMS cordless presses
–10 °C – +60 °C (14 °F – +140 °F)
Battery
–10 °C – +60 °C (14 °F – +140 °F)
Rapid charger
0 °C – +40 °C (32 °F – +113 °F)
Mains operated presses
–10 °C – +60 °C (14 °F – +140 °F)
Storage temperature range
> 0°C (32 °F)
1.4. Thrust
Thrust of radial presses, without Mini radial press
32 kN
Thrust REMS Mini-Press ACC / Mini Press 22 V ACC
22 kN
Thrust REMS Ax-Press 25 ACC
20 kN
Thrust REMS Ax-Press 25 L ACC
13 kN
Thrust REMS Ax-Press 30 / Ax-Press 40
30 kN
Thrust REMS Akku-Ex-Press Cu ACC / P / P ACC / Q&E ACC
20 kN
Thrust REMS Power-Ex-Press Q & E ACC
34 kN
The specified forces are nominal forces.
1.5. Electric Data
REMS Power-Press SE
230 V~; 50 – 60 Hz; 450 W; 1.8 A
REMS Power-Press
110 V~; 50 – 60 Hz; 450 W
REMS Power-Press ACC
S3 20% (AB 2/10 min)
REMS Power-Press XL ACC
all-insulated, interference-suppressed
REMS Power-Ex-Press Q & E ACC
REMS Mini-Press ACC
REMS Ax-Press 25 ACC / 25 L ACC
REMS Akku-Ex-Press Cu ACC
14.4 V =; 1.5 Ah
REMS Akku-Ex-Press P
14.4 V =; 3.0 Ah
REMS Akku-Ex-Press P ACC
REMS Akku-Ex-Press Q & E ACC
REMS Mini-Press 22 V ACC
21.6 V =; 1.5 Ah / 21.6 V =; 2.5 Ah
REMS
Ax-Press 30
16
