background image

- 4 - 

4B.  USING THE TX-2 WITH AN RCS “LOW OFF” ESC’. 

 

 

The TX-2 can be used with RCS LOW OFF ESC’s such as the Rx65b, ALPHA-3v2 & OMEGA-3v6k. 
We use the # Rx65b, ALPHA-3v2 set to “LOW OFF”.  The Ch # 5 Bind button is programmed as a sound trigger. 
This TX-2 hand piece is essentially a 5 channel stick R/C in a smaller case. 
Make sure the large throttle knob is fully CCW (OFF) and small knob is centered before you switch the system on. 
Switch on the TX-2 first & then the ESC. (Unless binding)  
1.  The large knob controls channel # 1, the throttle.  Make sure the knob is fully CCW before switching on.  This is the 
same as the Channel # 1 stick being fully down. 
2.  The small knob is the same as a Ch # 3 elevator stick.   
Turning the small knob to the right (CW) is the same as pushing the elevator stick forwards. 
Turning the small knob to the left (CCW) is the same as pulling the elevator stick backwards. 
3.  From neutral, set the small knob to the direction you want and leave it there.  CW for forwards. 
4.  Twist the large throttle knob to the right (CW) to accelerate. 
5.  To slow down twist the large knob to the left (CCW) until desired speed is reached. 
6.  To stop loco turn the large knob fully to the left (CCW).  Ignore the knob Centre “Click”. 
Throttle must be at OFF before changing direction.  Pause at neutral for one second when changing direction.   
7.  To select reverse direction turn the small knob to the left (CCW) and leave it there. 
To speed up, slow down & stop in reverse, repeat steps 4, 5, 6, & 7. 

 

 

 

 

SET THE FORWARDS DIRECTION. 

SET THE REVERSE DIRECTION. 

INCREASE THE SPEED 

 

 

Summary of Contents for TX-2

Page 1: ... THE 9 VOLT BATTERY LED BLINKS WHEN BATTERY LOW A HIGH QUALITY 9V SNAP IS USED WHEN USED FOR BATTERY R C LARGE KNOB HAS CENTRE CLICK OFF WITH 150º EITHER SIDE SETS THE DIRECTION SPEED 3 X BUTTONS FOR SOUND TRIGGER FOR USE WITH CENTRE OFF BATTERY R C ESC s MOST RCS LOW OFF ESC s THE TX 2 IS NOT SUITABLE FOR USE WITH LIVE STEAM LOCOS THE TX 2 IS GUARANTEED FOR ONE YEAR When used for battery R C you ...

Page 2: ...ON and the RX LED will blink slowly looking for a TX Wait 20 seconds for the RX to enter bind mode The RX LED slave front headlight if programmed to will blink rapidly and is ready to be bound FUNCTIONS OF TX 2 ON OFF SWITCH BUTTONS TO HOLD DURING BINDING 1 4 Press and hold the right pushbutton on the handpiece marked with a hexagonal symbol You may need to keep TX RX about 1 x metre apart for bin...

Page 3: ... OFF The Ch 5 Bind button is programmed as a sound trigger The RCS OMEGA 3v6 ESC cannot be used in CENTRE OFF format The TX 2 can be used intuitively with most of the centre off ESC s that are available The large knob uses Ch 1 to control both the direction speed It is most important that this large knob is centered at the built in Centre Click before switching the TX 2 on The dot on the knob shou...

Page 4: ...s a Ch 3 elevator stick Turning the small knob to the right CW is the same as pushing the elevator stick forwards Turning the small knob to the left CCW is the same as pulling the elevator stick backwards 3 From neutral set the small knob to the direction you want and leave it there CW for forwards 4 Twist the large throttle knob to the right CW to accelerate 5 To slow down twist the large knob to...

Reviews: