background image

7.5  Setting the Temperature

Set the required (maximum) domestic hot water temperature on the controller under "Para". To ensure that

scalding cannot occur at the water valve, the maximum hot water temperature must not exceed 60 °C.

Primary side

The temperature required in the buffer tank on the primary side depends on the desired hot water tempera-

ture and the required dispensing quantity. The temperature in the buffer tank must be at least 5 K above the

required hot water temperature.

Secondary side

The possible dispensing medium flow rate [l/min] on the water valve depends on the hot water temperature

that is set in the controller and the temperature that is available in the storage tank. The recommended max-

imum domestic water medium flow rate through the fresh water module is 25 l/min. The following table

shows the relationship between the storage tank temperature and the maximum dispensing medium flow

rate that is connected when the temperature on the valve is 45 °C (e.g. single-lever mixer). If the hot water

temperature that is set on the Controller is higher than 45 °C, the dispensing medium flow rate consists of a

mixture of hot and cold water. The transmission capacity that is specified for this is required to warm the

water quantity of the dispensing medium flow rate [l/min] from 10 °C to 45 °C.

EFS 35 Single and Duo

Tempera-

ture in

buffer

tank

probe

S08

[°C]

HW tem-

perature

set on

the con-

troller

[°C]

Maximum medium

flow rate from the

fresh water station

with the set. HW

temperature

[l/min]

Maximum dis-

pensing medium

flow rate at the

water valve for an

HW Temperature

of 45 °C

[l/min]

Transmission

capacity of the fresh

water station

[kW]

Return

tempera-

ture to

the

storage

tank

[°C]

 

 

Single

Duo

Single

Duo

Single

Duo

 

45

40

34

68

---

---

71

142

20

50

40

44

88

---

---

92

184

18

45

32

64

---

---

79

158

22

55

40

53

106

---

---

111

222

16

45

42

84

---

---

102

204

19

50

31

62

35

70

87

174

24

60

40

61

122

---

---

128

256

15

45

50

100

---

---

121

242

17

50

40

80

45

90

111

222

21

55

30

60

39

78

95

190

27

65

40

65

130

---

---

135

270

14

45

57

114

---

---

138

276

16

50

47

94

53

106

131

262

19

55

39

78

49

98

120

240

23

60

15

30

42

84

103

206

29

70

40

65

130 

*)

---

---

135

270

13

45

64

128

---

---

155

310

14

50

54

108

61

122

149

298

17

 

 

 

REMKO fresh water station

 

 

22

Summary of Contents for EFS 35

































Reviews: