SHORT TAPERED STYLES – “FLAT TOPS” &
SHORT CUTS
1.
Starting with the longest Guide Comb
attached (25mm), cut from the back of the
neck to the crown. Hold the Guide Comb
flat against the head and slowly move the
clipper through the hair, as shown.
2.
Use the same procedure from the lower
side to the upper side of the head, as
illustrated. Then cut the hair against the
direction in which it grows and level with
the sides.
3.
To give a “flat top” look, the hair on top of
the head must be cut over the top of a flat
comb
4.
Use a closer Guide Comb to taper the hair
down to the neckline as desired.
Cleaning & Maintaining Your
Clipper
AFTER EACH USE
High Precision
™
Hair Clipper is washable
enabling use in the shower and ease of
cleaning. Therefore, to maintain the perform-
ance of the cutters and trimmer, oil lightly
before and after each use.
■
Brush or rinse the accumulated hair from
the cutters. Do not submerge the clipper
in water.
■
Place one or two drops of cutter oil on
the blades. Turn the clipper on to
distribute the oil evenly. Wipe off any
excess oil.
■
To clean the unit, wipe with a damp cloth
and dry immediately.
!
Be sure the clipper is turned off when
applying the oil.
CHARGING YOUR HAIR
CLIPPER
Turn the clipper off
■
Insert the adapter plug into the bottom of
the clipper and plug the adapter unit into
a power outlet. The red light will glow to
indicate that it is charging.
■
The clipper will be fully charged in
14-16 hours.
■
The batteries cannot be overcharged, but
we recommend that charging be discon-
tinued if the clipper will not be used for a
long period of time.
■
It is advisable not to use this clipper
directly from the power outlet when it
has been fully charged, but if while using
the clipper in cordless mode there is a
noticeable drop in power, you can use
directly from the power outlet. Never
use under water when connected to
the outlet.
■
If the clipper has not been used for a
month or longer, it is advisable to
recharge it for 14-16 hours.
■
To preserve the life of the batteries,
discharge them by running the clipper
until the blades move slowly. Switch
off and fully recharge. Do this every
six months.
■
Charge the clipper at temperatures
between 40º-90ºF.
■
Nickel-Cadmium batteries included.
See battery removal section for
proper disposal of batteries.
INSTRUCTIONS FOR HAIR
CUTTING
Before starting the cut
1.
Inspect the clipper making sure that it is
free from hair and dirt.
2.
Seat the person so that their head is
approximately at your eye level.
3.
Before cutting, always comb the hair so it is
tangle free and as it is naturally worn.
4.
Hair must be dry.
6
How to Use
Reminders:
Cut the hair gradually using short strokes
only to work gradually over the entire head.
Always take off a little hair at a time. You
can always trim off additional hair later.
As you work, comb the hair frequently back
into the style that you are cutting. Each
comb attachment is marked accoringly on
its outside middle surface.
BEST TECHNIQUE
These instructions are only to be used as a
guide. You may prefer to begin trimming
with a longer comb attachment to avoid
cutting hair too short. As you become
familiar with the settings, you can select
your desired length setting.
STEP 1 – Nape of the neck – Diagram 1
1.
Use 3mm or 7mm
Guide Comb.
2.
Hold the clipper with
the cutting edge
pointed up and
begin the haircut.
Start at the center
of the head at the
base of the neck.
3.
Hold the clipper lightly against the head
with the comb teeth pointing upward.
Slowly lift the clipper, working upwards and
outwards through the hair, trimming just a
little at a time.
STEP 2 – Back of the head – Diagram 2
With the 12mm or
18mm Guide Comb
attached, cut the hair
at the back of the
head.
STEP 3 – Side of the head – Diagram 3
With the 3mm or 7mm
Guide Comb attached,
trim sideburns. Then,
change to the longer
9mm Guide Comb and
continue to cut the top
of the head.
STEP 4 – Top of the head – Diagram 4
1.
With the 18mm or
25mm Guide Comb
attached, cut hair on
top of the head
against the direction
in which the hair
normally grows.
2.
For longer hair on
top, use without a
Guide Comb. Lift the hair on top of the
head with a hand comb. Cut over the
hand comb with the hair lifted or hold
the hair between the fingers and cut it
to the desired length.
3.
Always work from the back of the head.
STEP 5 – The finishing touches – Diagram 5
1.
Use the clipper with
out an attachment
comb for close
trimming around the
base and sides of
the neck. Use the
ear comb guides to
obtain a clean line
around each ear. When using the ear comb
guide, angle the clipper and lightly stroke
around each ear towards the back of the
neck.
2.
To produce a clean straight line at the
sideburns, reverse the hair clipper. Press
the reversed clipper at right angles to
the head, tips of the blades lightly
touching the skin and then work
downwards.
7
1
3
2
4
5
28116_HC-600_IB 9/1/05 10:25 AM Page 6
