background image

12

S

ection

 2 — A

SSembly

 & S

et

-U

p

1. 

Remove lock nuts (a) and hex screws (b)

from chute support bracket (this will 

require two wrenches). See Figure 2-30.

Chute 

Assembly

Chute Base

Chute 

Support 

Bracket

Chute 

Control Head

(a)

(a)

(b)

(b)

Figure 2-30

2. 

Place chute assembly onto chute base 

and chute control head onto chute 

support bracket. See Figure 2-30.

3. 

Secure chute control head to chute 

support bracket with lock nuts (a) and 

hex screws (b) removed in Step 1. 

See Figure 2-31.

(a)

(a)

(b)

(b)

Figure 2-31

4. 

Remove hairpin clip (a) from rear of 

chute control assembly. See Figure 2-32.

5. 

Insert flex shaft (b) removed during 

Handle Assembly from lower handle into 

rear of chute directional control head. 

See Figure 2-32. Secure flex shaft to 

chute control head with hairpin clip (a) 

removed in Step 4.

(a)

(b)

Figure 2-32

6. 

Insert hex end of flex shaft into chute 

control rod coupling under dash panel.  

See Figure 2-33.

Figure 2-33

7. 

Ensure speed selector is in fastest 

forward speed.

8. 

Remove cotter pin (a) and washer (b) 

from ferrule on end of shift rod. See 

Figure 2-34 inset.

(a)

(b)

Shift Rod

Ferrule

Figure 2-34

9. 

Insert ferrule into top hole of shift 

lever and secure with cotter pin (a) and 

washer (b) removed in Step 8. Ferrule 

may need to be adjusted up or down.

10. 

Check that all cables are properly routed 

through cable guide on top of engine. 

See Figure 2-28.

STOP

STOP! Continue to Set-Up 

(page 14).

 

Overhead Chute Control (with Flex Shaft and Steel Chute)

Figure 2-29

Summary of Contents for 500

























Reviews: