Remington 500 Operator'S Manual Download Page 5

Page: 5 / 24

Assembly & Set-Up

Thank you for purchasing this product. It was carefully engineered to

provide excellent performance when properly operated and maintained.
Please read this entire manual prior to operating the equipment. It instructs

you how to safely and easily set up, operate and maintain your machine.

Please be sure that you, and any other persons who will operate the

machine, carefully follow the recommended safety practices at all times.

Failure to do so could result in personal injury or property damage.
All information in this manual is relative to the most recent product

information available at the time of printing. Review this manual frequently

to familiarize yourself with the machine, its features and operation. Please

be aware that this Operator’s Manual may cover a range of product

specifications for various models. Characteristics and features discussed

and/or illustrated in this manual may not be applicable to all models. We

reserve the right to change product specifications, designs and equipment

without notice and without incurring obligation.
If applicable, the power testing information used to establish the power

rating of the engine equipped on this machine can be found at www.opei.

org or the engine manufacturer’s web site.
If you have any problems or questions concerning the machine, phone your

local authorized service dealer or contact us directly. We want to ensure

your complete satisfaction at all times.
Throughout this manual, all references to

right

and

left

side of the machine

are observed from the operating position.

Thank You

Contents of Carton

•

Snow Thrower (1)

•

Chute Assembly (1)

•

Chute Control Rod, Flex Shaft, or Side

•

Replacement Auger Shear Pins (2-4)

•

Safety Key (2)

Crank Rod Assembly† (1)

•

Snow Thrower Operator’s Manual (1)

•

Engine Operator’s Manual (1)

•

Parts/Warranty Document (1)

•

Product Registration Card (1)

† If Equipped

NOTE:

This Operator’s Manual covers several models. Features may vary by model. Not all features in this manual are applicable to all models and the

model depicted may differ from yours. Refer to Figure 2-1 which shows the different versions and match the contents of carton (chute and directional

control rod/flex shaft) to identify your specific unit.

Overhead Chute Control

(with Flex Shaft and Steel Chute)

Page 12

Electric Chute Control

Pages 13

U-Joint Side Crank Chute Control

Page 8

Two & Four Way Chute Control

Pages 10-11

Overhead Chute Control (with Chute Control Rod)

Page 9

Standard Side Crank Chute Control

Standard Side Crank

Rod Assembly

U-Joint Side Crank

Rod Assembly

Overhead Chute

Control Rod

Chute Control Rod

Flex Shaft

Manual Chute

Control Rod

Chute

Assembly

Chute

Assembly

Chute

Assembly

Chute Assembly

Chute

Assembly

Page 7

Figure 2-1

Summary of Contents for 500

























Search results

Summary of Contents for 500

Reviews:

Related manuals for 500

Brands by name

Popular brands

Remington 500, Operator'S Manual

Search results

Summary of Contents for 500

Reviews:

Related manuals for 500

Brands by name

Popular brands