background image

REMET CNC TECHNOLOGY SP. Z O.O.

 

 

Page 25 of 28 

Producer of machinery and equipment, machining

 

11.

 

 MAINTENANCE AND CLEANING 

Safety instructions for maintenance. 

 

The device must be disconnected from the power source and placed on a 

stable, even and non-slippery surface before carrying out maintenance or repairs. 
Clean the device before and after each use, and check the tightness of the screws 
that secure the covers. 

General activities related to maintenance and cleaning 

The device should be kept clean at all times. To clean the device, use only a 

brush or cloth. Never use solvents or cleaning agents. 

Check all covers and protective elements are undamaged and in the correct 

place. Replace if necessary. Pay special attention to loose and worn parts. Check 
for screws and the nuts are tight 

 
 
 
 

12.

 

DISPOSAL AND ENVIRONMENT PROTECTION 

 

Dispose the device, accessories and packaging in accordance with environmen-

tal protection requirements at specialist disposal points. 

The device can not be disposed of with household waste. Protect the environ-ment. 
The device should be returned to the local recycling point. Disposal is free. More 
information can be obtained at the disposal point. Incorrect disposal can be pu-
nished in accordance 
with local regulations. 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

 

Summary of Contents for RT-690R






























Reviews: