Reliable DDX Instructions For Installation, Operation And Maintenance Download Page 8

Technical Data

Reliable Double Interlock Type D Preaction Systems, with 

associated trim, size 2” (50 mm), 2½” (65 mm), 76 mm, 
3” (80 mm), 4” (100 mm), 165 mm, 6” (150 mm), 8” (200 
mm) are rated for use at minimum water supply pressure of 
20 psi (1.4 bar) and maximum supply pressure of 250 psi 
(17.2 bar) for 2” (50mm), 21/2” (65mm), 3” (80mm), 76mm 
and 8” (200mm) valve sizes and 300 psi (20.7 bar) for 4” 
(100mm), 6” (150mm) and 165mm valve sizes. Water sup-
plied to the inlet of the valve and to the pushrod chamber 
must be maintained between 40°F (4°C) and 140°F (60°C).

The following list of technical bulletins pertains to valves 

and devices that may be used in this preaction system:

Deluge Valve 

Reliable 519

Hydraulic Emergency Station
(Model A)

Reliable 506

Mechanical Sprinkler Alarm

Reliable 612/613

Pressure Maintenance Device 

Reliable 251

Nitrogen Regulating Device                             Reliable 254

Releasing/Control Panel

Potter #5403550

Low Air Pressure Supervisory Switch Potter 5400928

Waterflow Pressure Alarm Switch 

Potter 5400928

Model DDX Deluge Valve Description

1.  Rated working pressure:

Valve & System - 250 psi (17.2 bar) for 2” (50mm), 2

1

/

2

” (65mm), 

3” (80mm), 76mm and 8” (200mm) valve sizes and 300 psi (20.7 
bar) for 4” (100mm), 6” (150mm) and 165mm valve sizes.

2.  Factory tested to a hydrostatic pressure of 500 psi (34.5 bar) for 

2” (50mm), 2

1

/

2

” (65mm), 3” (80mm), 76mm and 8” (200mm) 

valve sizes and 600 psi (41.7 bar) for 4” (100mm), 6” (150mm) 
and 165mm valve sizes. (Valve only)

3.  End and trim connections:

• 

ANSI/AWWA C606 grooved inlet and outlet

Nominal Pipe 

Size

Outlet Diam-

eter

Groove 

Diameter

Groove 

Width

Outlet Face 

to Groove

2”

(50 mm)

2.375”

(60 mm)

2.250”

(57 mm)

11/32”

(9.0 mm)

5/8”

(16 mm)

2½”

(65 mm)

2.875”

(73 mm)

2.720”

(69 mm)

11/32”

(9.0 mm)

5/8”

(16 mm)

76 mm

3.000”

(76 mm)

2.845”

(72 mm)

11/32”

(9.0 mm)

5/8”

(16 mm)

3”

(80 mm)

3.500”

(89 mm)

3.344”

(85 mm)

11/32”

(9.0 mm)

5/8”

(16 mm)

4”

(100 mm)

4.500”

(114 mm)

4.334”

(110 mm)

3/8”

(9.5 mm)

5/8”

(16 mm)

165 mm

6.500”

(165 mm)

6.330”

(161 mm)

3/8”

(9.5 mm)

5/8”

(16 mm)

6”

(150 mm)

6.625”

(168 mm)

6.455”

(164 mm)

3/8”

(9.5 mm)

5/8”

(16 mm)

8”

(200 mm)

8.625”

(219 mm)

8.441”

(214 mm)

7/16”

(11 mm)

3/4”

(19 mm)

•     Threaded openings Per ANSI B 2.1

•     Flange Dimensions

Flange 

Type:

Nominal 

Pipe 

Size

Bolt 

Circle 

Diameter

Bolt

Hole

Diameter

Flange 

Outside 

Diameter

Flange 

Thick-

ness

Number

of

 Bolts

ASME B16.5 

Class 150

4” 

(100mm)

7½” 

(191mm)

¾”

(19mm)

9” 

(229mm)

15

/

16

(24mm)

8

ISO 7005-2 

PN16

4” 

(100mm)

7

3

/

32

” 

(180mm)

¾”

(19mm)

9” 

(229mm)

15

/

16

(24mm)

8

ASME B16.5 

Class 150

6” 

(150mm)

9½” 

(241mm)

7

/

8

” 

(22mm)

11” 

(279mm)

15

/

16

(24mm)

8

ISO 7005-2 

PN16

6” 

(150mm)

9

7

/

16

” 

(240mm)

29

/

32

” 

(23mm)

11” 

(279mm)

15

/

16

(24mm)

8

ASME B16.5 

Class 150

8” 

(200mm)

11¾” 

(298mm)

7

/

8

” 

(22mm)

13½” 

(343mm)

1” 

(25.4mm)

8

ISO 7005-2 

PN16

8” 

(200mm)

11

5

/

8

” 

(295mm)

29

/

32

” 

(23mm)

13½” 

(343mm)

1” 

(25.4mm)

12

4.  Valve Color:

Valve Size

Color

2” (50 mm)

Black or Red

2½” (65 mm)

Black or Red

76 mm

Red

3” (80 mm)

Black or Red

4” (100 mm)

Black or Red

165 mm

Red

6” (150 mm)

Black or Red

8” (200 mm)

Black or Red

5.  Face to face dimensions:

Valve Size:

End

Connection:

End to End:

2" (50mm), 2½" (65mm), 

76mm & 3" (80mm)

Groove/ Groove

12½" (318mm)

4" (100mm)

Groove/ Groove

14" (356mm)

Flange/ Groove

16" (406mm)

Flange/ Flange

16" (406mm)

6" (150mm) & 165mm

Groove/ Groove

16" (406mm)

Flange/ Groove

19" (483mm)

Flange/ Flange

19" (483mm)

8" (200mm)

Groove/ Groove

19

3

/

8

” (492mm)

Flange/ Flange

21¼" (540mm)

6.  Valve shipping weight:

Valve Size:

End Connection:

Weight:

2" (50mm), 2½" (65mm), 

76mm & 3" (80mm)

Groove/ Groove

34 lbs (15 kg)

4" (100mm)

Groove/ Groove

64 lbs (29 kg

Flange/ Groove

79 lbs (36 kg)

Flange/ Flange

92 lbs (42 kg)

6" (150mm) & 165mm

Groove/ Groove

95 lbs (43 kg)

Flange/ Groove

122 lbs (56 kg)

Flange/ Flange

138 lbs (69 kg)

8" (200mm)

Groove/ Groove

148 lbs (67 kg)

Flange/ Flange

197 lbs (90 kg)

7.  Trim shipping weight:

Trim Configuration

2” (50 mm),

2½” (65 mm),

3” (80 mm)

& 76 mm

4” (100 mm),
6” (150 mm),

8” (200 mm)

& 165 mm

Type D Double Interlock

47 lbs (21 kg)

52 lbs (24 kg)

8.

Summary of Contents for DDX


















Reviews: