background image

Intended Use

This product is intended to be used for; the lifting 
of goods, or the lifting of persons providing there 
is no risk of a fall.

This product provides a safety anchor point on the 
column for the prevention of falls of the person 
operating the davit only.

It is expected that all users of this product have the 
necessary medical and physical capabilities, are fully 
trained and competent in its safe assembly and use.

Correct Operation

Inspection Prior to Initial Operation

Each product must be inspected prior to initial 

operation by a competent person to ensure that the 

structure is safe and that it has not been damaged 

by incorrect assembly, transport or storage. 

Inspection Before Starting Work

Before starting work, the product assembly and 
all load-bearing components should be checked 
for visual defects as per the inspection checklist on 
page 8.

Maximum Capacity

Goods Lifting:

 This product is designed to lift 

and lower loads up to its rated capacity. Do not 
exceed the capacity indicated on the product.  

Personnel Lifting: 

When lifting people, the 

overall load limit is reduced by half to provide an 
increased safety factor.  The maximum capacity 
permitted by the personnel winch/accessory used 
in conjunction with the product also needs to be 
taken into account. 

If this product is to be used for lifting or lowering 
a person where there is a risk of a fall, then 
a secondary line/fall arrest unit is required, 
connected to a separate structure which meets 
the requirements of OSHA 1926 Subpart M.

Only chain hoists with a capacity of up to 2200lb 
are suitable for this product. The structure has 
been designed to take into account the weight 
of a standard chain block but, if a device with 
a significant additional weight is being used, 
then this needs to be included within the overall 
capacity. Care should also be taken when using 
any lifting device other than a manual chain 
hoist in case the dynamic effects of this reduce 
the overall capacity of the davit. REID Lifting’s 
representatives can provide additional advice on 
this if required.

Please be aware that the maximum reach is 
achieved when the davit is being used at 
approximately 75% of its maximum capacity.

Summary of Contents for T DAVIT





































Reviews: