9
PORTA
GANTRY
500-3000
Fall Protection Applications
Use as a Fall Protection Anchor
When being used as part of a fall protection
system the user must use a body harness and
retractable device or shock absorber to EN355 that
limits the maximum allowed force (M.A.F.) to 6kN.
Winches used with the system should comply to
EN1496:2017 or equivalent.
In the event of simultaneous goods and personnel
combined lifting/ fall arrest or when being used as
a fall arrest system in sub-zero and wet conditions
contact the supplier as capacities may be reduced.
Only one person should be attached to each
trolley in accordance with the notified working
load limit (WLL). Each lift must be properly
planned, and all weights clearly known along with
the WLL and constraints of all personal fall arrest
system components.
The capabilities stated in the table apply to
standard range systems only. If unsure about
your system consult serial labels, information
filled in on page 31 or consult your supplier.
Bespoke versions of the system are available
tailored to specific lifting needs. These versions
are designated with a ‘C’ at the end the product
number on the serial label attached to each
A-Frame and beam.
For custom designed gantries please contact your
supplier for appropriate rating and capabilities.
Additional Notes for Correct Operation
The anchorage must always be above the users
head to prevent dangerous free falls.
Always carry out pre-use checks before using
this equipment. It is advised to use a buddy
system and inspection must be by a competent
person.
The fall arrest device must only be attached to
the lifting point on the trolley or the designated
location on the cheek plate or upright. (see
product images and set up instructions).
Only use the product for fall arrest applications
when the castor brakes are engaged.
To ensure stability of the structure, the
operating span of the beam must be equal
to or greater than the distance between the
castors on the A-Frames.
Never walk away from the footprint of the
product or move outside designated safe
zones whilst connected to it where there is a
risk of a fall (refer to figure B). Ensure that the
operating area is within the footprint of the
system before beginning work.
When using the product as a fall arrest anchor
ensure there is adequate fall clearance
when working at height (refer to figure C). A
competent person should calculate this taking
into account all of the components of the
personal fall arrest system and allowing a safety
margin.
Only use the product for fall arrest applications
when the castor brakes are engaged.
Always consider the potential effects of
sharp edges, chemical reagents, electrical
conductivity, cutting, abrasion, climatic
exposure on all components of the fall
protection system, and the effect of offset
forces as a result of pendulum falls.
If the product has been subjected to a fall
arrest or impact force it must be immediately
removed from service.
Ensure the structure on which the product is
mounted is horizontal. If necessary, adjust the
products feet to achieve a level operating
structure.
The substrate of the structure on which the
product is placed must be able to sustain the
loads specified for the device in all orientations
permitted, including a safety factor of at least 2.
Never exceed the number of allowable users.
Never adjust the product whilst a person is
attached to it.
Only use designated anchor points for the
attachment of fall protection devices.
Ensure that any fall protection system
components being used are compatible and
meet the requirements of applicable standards.
When using this equipment ensure that there is
a rescue plan prior to starting work and ensure
that users are trained in the correct execution
of the plan and have all necessary rescue
equipment to hand.
Where required by regulation, each installation
must be approved by a qualified person.
Always wear appropriate PPE when installing,
setting up, dismantling and using this
equipment.
Misuse of this product could result in serious
injury or death.
*Only Applicable to systems being used in accordance with PD CEN/TS 16415:2013. When
being used in accordance with EN795:2012, the structure shall be limited to a maximum of
one user
Application
Capacity
Goods [kg]
500
1000
2000
3000
Fall Arrest*
3 persons 3 persons 5 persons 5 persons
Personnel [kg]
250
500
1000
1500
This product has different ratings depending
upon the application:
B
C
The system is not suitable for fall arrest
applications.
The system is suitable for fall arrest applications. Specify
number of users. Max weight of 150kg.
