background image

  Version 06/21                                                                                  Page  7 of 23                                                                             ICON 35 UM EN 

WARNING!  Always  ensure, that  the  brake  is applied,  when  the  Attendant  is  leaving  the  wheelchair  with  the 
User sitting in it. 

 

WARNING!  Always  ensure,  that  the  front  casters  always  point  forwards,  if  the  wheelchair  stands  still,  to 
enlarge their contact with the base.

 

 

How to ride on a threshold 

 

 

 
User facing the threshold

 

(

We  advise,  to  use  the  below  mentioned  technique  only  by  experienced 

wheelchair Users)

 

Drive the wheelchair as close to the threshold as possible

 

Incline the wheelchair backwards balancing on the rear wheels and lift the front turning 
wheels to the height of the threshold. Push the rear wheels forwards and in the same 
time lean over transferring the weight to the front of the wheelchair.

 

 

 

 
 
Attendant and User facing the threshold  
The Attendant inclines the wheelchair backwards by using the step pedal, allowing the 
front casters to come off the base. Drive forward until the rear wheels touch the edge.

 

Use the handles at the back of the wheelchair to lift the rear wheels on the threshold.

 

 

 

 
 
Users with their back to the threshold

 

(The  below  mentioned  technique  will  only  work  in  case  of  a  low  threshold  and  if  the 
legrests don't touch the ground.

 

Drive to the threshold backwards until the rear wheels touch it. Push the rear wheels 
backwards leaning forwards at the same time.

 

 

 

 

 

 

Attendant and User with their back to the threshold

 

Drive  to  the  threshold  so  that  the  rear  wheels  touch  the  edge.  Tilt  the  wheelchair 
backwards with use of the step pedal allowing the front casters to come off the base as 
much as it is necessary. Pull the wheelchair backwards on the threshold until the front 
casters are above the threshold. Then carefully lower the front casters onto the base. 

 

 

 

How to ride down from a threshold  

 

User facing the thresholds edge 

 

(We  advise,  to  use  the  below  mentioned  technique  only  by  the  experienced  wheelchair 
Users) 

 

Drive the wheelchair as close as possible to the edge.

 

Balance the wheelchair on the rear wheels allowing the front turning wheels to come off the 
base as much as it is necessary. 

 

Drive  from  of  the  edge  very  slowly  and  carefully  lowering  the  front  turning  wheels  on  the 
base.

 

 

 

Summary of Contents for ICON 35
























Reviews: