manualshive.com logo in svg

Regulus 18514, Instruction Manual

Share
Download
Regulus 18514 Instruction Manual Download Page 28

28 

 

 

Building overheating at temperatures above zero 

If a building overheats at an 

outdoor temperature above zero, 

the heating water temperature shall 

be reduced with the minus button. 

The graph shows that the heating 

water temperature will be adjusted 

mainly at temperatures above zero. 

 

Building underheating at temperatures above zero 

 

If a building underheats at an 

outdoor temperature above zero, 

the heating water temperature shall 

be increased with the plus button. 

The graph shows that the heating 

water temperature will be adjusted 

mainly at temperatures above zero. 

 

 

Building overheating at temperatures below zero 

If a building overheats at an 

outdoor temperature below zero, 

the heating water temperature shall 

be reduced with the minus button. 

The graph shows that the heating 

water temperature will be adjusted 

mainly at temperatures below zero.

 

Summary of Contents for 18514









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands