background image

INSTALLATION REQUIREMENTS

A 220/240-volt, 50 Hz, AC -only 13 amp fused, grounded electrical power 
supply is required. It is recommended that a separate circuit serving only 
electronic instant hot water appliance be provided or use an outlet that 
can be turned on/off by a switch.

This electronic instant hot water appliance is equipped with a power supp-
ly cord with a power plug. To minimise possible shock hazard, the cord m-
ust be plugged into mating, ground-type outlet, grounded in accordance 
with all national and local codes and ordinances.If a socket outlet is not 
available, it is the responsibility and obligation of the customer to have a 
properly grounded outlet installed by a qualified electrician.  

Don’t install the electronic instant hot water appliance outdoors or in 
location that may fall below zero degrees C, otherwise the pipes and the 
tap will be frozen and there will be serious safety trouble, possible 
bodilyinjury, accidents and damage caused.

It’s forbidden to wash the electronic instant hot water appliance with water 
directly.

The installation environment should be ventilated, with protection from 
the direct sunshine.

When installing the electronic instant hot water appliance, provide 
approximately 10cm to 15cm (4-51/2") of air space on the sides of the unit 
for air circulation and approximately 2.5cm(1") from the mounting wall.

The environment humidity should be in the range of  10% to 60%. Be sure 
there is no dew.

If local codes permit, the instant hot water tap feed line should be 
connected to the hot and cold water supply line using isolation valves or 
another means for providing the hot and cold water to the tap.

IMPORTANT: If local codes do not permit the use of isolation valves, 
special feed valves can be obtained from your local plumbing supply 
distributor.

Connecting a standard Tap may cause injury and will damage the 
electronic instant hot water appliance and void the guarantee. Due to high 
water temperature, and for safety reasons, the electronic instant hot 
water appliance is not under pressure.

Summary of Contents for Amanzi















Reviews: