Regency P33E-4 Owners & Installation Manual Download Page 43 | Manualshive

Page: 43 / 68

background image

Regency® P33E-4 Zero Clearance Direct Vent Gas Fireplace

43

INSTALLATION

OPTIONAL BAY DOOR

The Bay louvers MUST be used

with the Bay glass option.

The optional Bay door is an overlay on the fl ush
front.

The standard fl ush door and glass must

remain on the unit.

1) Hook the top of the bay door over the fl ush

door fl ange and swing the bottom against the
bottom fl ange of the fl ush door.

2) Secure

to

the

fl ush door bottom bracket with 2

screws provided.

Diagram 1

Diagram 2

FLUSH LOUVERS

1)

Install the top louver by sliding the two bracket

clips into the brackets located underneath the
top of the fi rebox.

2)

Install the bottom louver by folding the louver

down and then sliding the Bottom Louver bracket
down onto the 2 pins on the base of the unit
(Diagram1). Secure with 1 screw (Diagram 2).

Note: Top and
bottom louvers
are different.

3)

Open the bottom louver. Pull the Burner ON/

OFF control box from inside the bottom of the
fi replace and position the slots in the bracket
over the 2 screws on the left side of the bottom
louver. Push down to lock into place. Tighten
the screws.

Screws on

louver bracket

Burner ON/OFF control box attached to

bottom fl ush louver.

Burner ON/OFF

control box

Note: If any maintenance etc. must be done in

the fi rebox, fi rst remove the Bay louvers
and door.

OPTIONAL BAY TRIM

Attach the 4 supplied magnets, each to the back of
the top and bottom trim pieces (space out evenly)
and attach trim to the top and bottom of Bay door.

DOUBLE SCREEN DOOR

1) Pull out the top louver.

2) Center the screen door and hook over the fl ush

door.

3) Open the screen door(s) and secure the screen

door to the fl ush door front with 2 clips on the
bottom left and right side.

Clip locations

Clip installed on right side.

«
...
41
42
43
44
45
...
»

Summary of Contents for P33E-4





































































Reviews:

No comments

Related manuals for P33E-4

emifocus hublot dv

Brand: Focus Pages: 8

Brand: Napoleon Pages: 144

Brand: Valor Pages: 38

Brand: Napoleon Pages: 20

CALAEVIN SP5560

Brand: Prokonian Pages: 16

Duraflame DFI030ARU

Brand: Twin-Star International Pages: 26

Superior Fireplaces DRT2000 Series

Brand: IHP Pages: 76

Brand: Napoleon Pages: 120

Brand: Enviro Pages: 48

Vail L-FT769PST

Brand: Sunjoy Pages: 5

Brand: Amantii Pages: 20

EF11-36 LIMOUSIN

Brand: Focal Point Pages: 13

Brand: Napoleon Pages: 60

Brand: Home Decorators Collection Pages: 20

Brand: Canvas Pages: 100

Brand: Touchstone Pages: 10

Brand: IHP Pages: 4

Brand: Piazzetta Pages: 61

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands