manualshive.com logo in svg

Regency P121-LP10, Owners & Installation Manual, Page: 44 / 48

Share
Download
Regency P121-LP10 Owners & Installation Manual Download Page 44

44

 | 

Regency

®

 P121-10/P131-10 Zero Clearance Direct Vent Gas Fireplace

 | 

44

parts list

P121-10/P131-10 BURNER ASSEMBLY & LOG SET

    

    Part # 

Description

 

 

360-930 

Log Set

41) *  

Front Right Log

42) *  

Front Left Log

43) *  

Middle Left Log

44) *  

Middle Right Log

 

363-574/P 

Valve Assembly -NG

 

363-576/P 

Valve Assembly -LP

56)   910-578 

Valve Only -NG

 

  910-580 

Valve Only -LP

57) 360-090 

Gasket - Valve Tray

58) *  

Valve Tray

 

66) 910-038 

Pilot Assembly - NG

 

910-039 

Pilot Assembly - LPG

 

67) *  

Pilot Holder

68) W840470 

Pilot Assembly Gasket

79) 360-525 

Burner Assembly

82) 360-027 

Grate Assembly

 

904-690 

Orifice #31 - NG

 

904-641 

Orifice #50 - LP

 

936-170 

Orifice Gasket

 

910-036  

Pilot Orifice NG

 

910-037  

Pilot Orifice LP

 

910-581  

Stepper motor NG

 

910-582  

Stepper motor LP

 

910-432  

Pilot tube with nuts

 

910-096  

3 way pilot hood

 

910-341  

Thermopile

 

910-386  

Thermocouple

 

910-073  

DC Spark box

 

910-074  

DC Spark box wire

 

910-572  

Remote receiver

 

911-127  

Remote receiver battery  

   

compartment door

 

910-592  

GTMF Remote control  

   

Hand held

 

911-164  

Valve wiring harness

 

W840470  

Pilot assembly gasket

 

*Not available as a replacement part.

 

Summary of Contents for P121-LP10

















































Reviews:

No comments