manualshive.com logo in svg

Regency P121-LP10, Owners & Installation Manual, Page: 2 / 48

Share
Download
Regency P121-LP10 Owners & Installation Manual Download Page 2

2

 | 

Regency

®

 P121-10/P131-10 Zero Clearance Direct Vent Gas Fireplace

 | 

2

To the New Owner:

Congratulations! 

You are the owner of a state-of-the-art Gas Fireplace by REGENCY

®

. The P121 /  P131 is a hand crafted appliance 

and has been designed to provide you with all  the warmth and charm of a wood fireplace at the flick of a switch.  

The model P121 / P131 has been approved by Intertek for both safety and efficiency.  As it also bears our own 

mark, it promises to provide you with economy, comfort and security for many trouble free years to follow.  Please 

take a moment now to acquaint yourself with these instructions and the many features of your Regency

®

 Fireplace.

IMPORTANT:  If the unit is to be installed into a bathroom, optional Neo ceramic glass Part# 360-946 Front or Part# 

360-948 Side must be purchased and installed in place of the tempered glass supplied with the unit.

Summary of Contents for P121-LP10

















































Reviews:

No comments