Regency L234-LP10 Owners & Installation Manual Download Page 1

Page: 1 / 48

Tested by:

Installer: Please complete the details on the back cover

and leave this manual with the homeowner.

Homeowner: Please keep these instructions for future reference.

Liberty

L234 Gas Insert

Owners & Installation Manual

MODELS: L234-NG10 Natural Gas L234-LP10 Propane

Liberty L234 Product Video

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other

appliance.

- WHAT TO DO IF YOU SMELL GAS
•

Do not try to light any appliance.

• Do not touch any electrical switch: do not use any phone in your building.

Leave the building immediately.

• Immediately call your gas supplier from a neighbour's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency or the gas supplier.

WARNING
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could result in serious
injury, death, or property damage.

919-442e

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4

09.29.20

Summary of Contents for L234-LP10

















































Search results

Summary of Contents for L234-LP10

Reviews:

Related manuals for L234-LP10

Brands by name

Popular brands

Regency L234-LP10, Owners & Installation Manual

Search results

Summary of Contents for L234-LP10

Reviews:

Related manuals for L234-LP10

Brands by name

Popular brands